mc9s08qg8 Freescale Semiconductor, Inc, mc9s08qg8 Datasheet - Page 150

no-image

mc9s08qg8

Manufacturer Part Number
mc9s08qg8
Description
Hcs08 Microcontrollers
Manufacturer
Freescale Semiconductor, Inc
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
mc9s08qg84CDNE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Part Number:
mc9s08qg84CDTE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Part Number:
mc9s08qg8CDT
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s08qg8CDTE
Manufacturer:
ABB
Quantity:
101
Part Number:
mc9s08qg8CDTE
Manufacturer:
Freescale Semiconductor
Quantity:
41 991
Part Number:
mc9s08qg8CDTE
Manufacturer:
FREESCALE
Quantity:
500
Part Number:
mc9s08qg8CDTE
Manufacturer:
FREESCALE
Quantity:
500
Part Number:
mc9s08qg8CDTE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s08qg8CDTER
0
Part Number:
mc9s08qg8CFFE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s08qg8CFFE
Quantity:
16
Part Number:
mc9s08qg8CFKE
Manufacturer:
FREESCALE
Quantity:
31 848
Part Number:
mc9s08qg8CFKE
Manufacturer:
FREESCALE
Quantity:
31 848
Part Number:
mc9s08qg8CPBE
Manufacturer:
CYPRESS
Quantity:
310
Part Number:
mc9s08qg8CPBE
0
Internal Clock Source (S08ICSV1)
times the filter frequency, as selected by the RDIV bits, so that the ICSLCLK will be available for BDC
communications, and the external reference clock is enabled.
10.4.1.6
The FLL bypassed external low power (FBELP) mode is entered when all the following conditions occur:
In FLL bypassed external low power mode, the ICSOUT clock is derived from the external reference clock
and the FLL is disabled. The ICSLCLK will be not be available for BDC communications. The external
reference clock is enabled.
10.4.1.7
Stop mode is entered whenever the MCU enters a STOP state. In this mode, all ICS clock signals are static
except in the following cases:
ICSIRCLK will be active in stop mode when all the following conditions occur:
ICSERCLK will be active in stop mode when all the following conditions occur:
10.4.2
When switching between FLL engaged internal (FEI) and FLL engaged external (FEE) modes the IREFS
bit can be changed at anytime, but the RDIV bits must be changed simultaneously so that the resulting
frequency stays in the range of 31.25 kHz to 39.0625 kHz. After a change in the IREFS value the FLL will
begin locking again after a few full cycles of the resulting divided reference frequency.
The CLKS bits can also be changed at anytime, but the RDIV bits must be changed simultaneously so that
the resulting frequency stays in the range of 31.25 kHz to 39.0625 kHz. The actual switch to the newly
selected clock will not occur until after a few full cycles of the new clock. If the newly selected clock is
not available, the previous clock will remain selected.
10.4.3
The BDIV bits can be changed at anytime and the actual switch to the new frequency will occur
immediately.
150
CLKS bits are written to 10.
IREFS bit is written to 0.
BDM mode is not active and LP bit is written to 1.
IRCLKEN bit is written to 1
IREFSTEN bit is written to 1
ERCLKEN bit is written to 1
EREFSTEN bit is written to 1
Mode Switching
Bus Frequency Divider
FLL Bypassed External Low Power (FBELP)
Stop
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 1.01
Freescale Semiconductor

Related parts for mc9s08qg8