mc9s08qg8 Freescale Semiconductor, Inc, mc9s08qg8 Datasheet - Page 202
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
mc9s08qg8
Manufacturer Part Number
mc9s08qg8
Description
Hcs08 Microcontrollers
Manufacturer
Freescale Semiconductor, Inc
Datasheet
1.MC9S08QG8.pdf
(300 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
mc9s08qg84CDNE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Company:
Part Number:
mc9s08qg84CDTE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Part Number:
mc9s08qg8CDT
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
mc9s08qg8CDTE
Manufacturer:
ABB
Quantity:
101
Company:
Part Number:
mc9s08qg8CDTE
Manufacturer:
Freescale Semiconductor
Quantity:
41 991
Part Number:
mc9s08qg8CDTE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s08qg8CFFE
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
mc9s08qg8CPBE
Manufacturer:
CYPRESS
Quantity:
310
Serial Communications Interface (S08SCIV3)
14.2.5
This register has one read-only status flag. Writes have no effect.
14.2.6
202
Reset
Reset
BRK13
Field
Field
RAF
R8
T8
2
0
7
6
W
W
R
R
SCI Status Register 2 (SCIS2)
SCI Control Register 3 (SCIC3)
Break Character Length — BRK13 is used to select a longer break character length. Detection of a framing
error is not affected by the state of this bit.
0 Break character is 10 bit times (11 if M = 1)
1 Break character is 13 bit times (14 if M = 1)
Receiver Active Flag — RAF is set when the SCI receiver detects the beginning of a valid start bit, and RAF is
cleared automatically when the receiver detects an idle line. This status flag can be used to check whether an
SCI character is being received before instructing the MCU to go to stop mode.
0 SCI receiver idle waiting for a start bit.
1 SCI receiver active (RxD input not idle).
Ninth Data Bit for Receiver — When the SCI is configured for 9-bit data (M = 1), R8 can be thought of as a
ninth receive data bit to the left of the MSB of the buffered data in the SCID register. When reading 9-bit data,
read R8 before reading SCID because reading SCID completes automatic flag clearing sequences which could
allow R8 and SCID to be overwritten with new data.
Ninth Data Bit for Transmitter — When the SCI is configured for 9-bit data (M = 1), T8 may be thought of as a
ninth transmit data bit to the left of the MSB of the data in the SCID register. When writing 9-bit data, the entire
9-bit value is transferred to the SCI shift register after SCID is written so T8 should be written (if it needs to
change from its previous value) before SCID is written. If T8 does not need to change in the new value (such as
when it is used to generate mark or space parity), it need not be written each time SCID is written.
R8
0
0
0
7
7
= Unimplemented or Reserved
= Unimplemented or Reserved
T8
0
0
0
6
6
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 1.01
Table 14-7. SCIC3 Register Field Descriptions
Table 14-6. SCIS2 Register Field Descriptions
Figure 14-11. SCI Control Register 3 (SCIC3)
Figure 14-10. SCI Status Register 2 (SCIS2)
TXDIR
0
0
0
5
5
TXINV
0
0
0
4
4
Description
Description
ORIE
3
0
0
3
0
BRK13
NEIE
0
0
2
2
Freescale Semiconductor
FEIE
0
0
0
1
1
PEIE
RAF
0
0
0
0