mc9s08qg8 Freescale Semiconductor, Inc, mc9s08qg8 Datasheet - Page 92
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
mc9s08qg8
Manufacturer Part Number
mc9s08qg8
Description
Hcs08 Microcontrollers
Manufacturer
Freescale Semiconductor, Inc
Datasheet
1.MC9S08QG8.pdf
(300 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
mc9s08qg84CDNE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Company:
Part Number:
mc9s08qg84CDTE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Part Number:
mc9s08qg8CDT
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
mc9s08qg8CDTE
Manufacturer:
ABB
Quantity:
101
Company:
Part Number:
mc9s08qg8CDTE
Manufacturer:
Freescale Semiconductor
Quantity:
41 991
Part Number:
mc9s08qg8CDTE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s08qg8CFFE
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
mc9s08qg8CPBE
Manufacturer:
CYPRESS
Quantity:
310
Chapter 7 Central Processor Unit (S08CPUV2)
7.4.3
The WAIT instruction enables interrupts by clearing the I bit in the CCR. It then halts the clocks to the
CPU to reduce overall power consumption while the CPU is waiting for the interrupt or reset event that
will wake the CPU from wait mode. When an interrupt or reset event occurs, the CPU clocks will resume
and the interrupt or reset event will be processed normally.
If a serial BACKGROUND command is issued to the MCU through the background debug interface while
the CPU is in wait mode, CPU clocks will resume and the CPU will enter active background mode where
other serial background commands can be processed. This ensures that a host development system can still
gain access to a target MCU even if it is in wait mode.
7.4.4
Usually, all system clocks, including the crystal oscillator (when used), are halted during stop mode to
minimize power consumption. In such systems, external circuitry is needed to control the time spent in
stop mode and to issue a signal to wake up the target MCU when it is time to resume processing. Unlike
the earlier M68HC05 and M68HC08 MCUs, the HCS08 can be configured to keep a minimum set of
clocks running in stop mode. This optionally allows an internal periodic signal to wake the target MCU
from stop mode.
When a host debug system is connected to the background debug pin (BKGD) and the ENBDM control
bit has been set by a serial command through the background interface (or because the MCU was reset into
active background mode), the oscillator is forced to remain active when the MCU enters stop mode. In this
case, if a serial BACKGROUND command is issued to the MCU through the background debug interface
while the CPU is in stop mode, CPU clocks will resume and the CPU will enter active background mode
where other serial background commands can be processed. This ensures that a host development system
can still gain access to a target MCU even if it is in stop mode.
Recovery from stop mode depends on the particular HCS08 and whether the oscillator was stopped in stop
mode. Refer to the
7.4.5
The BGND instruction is new to the HCS08 compared to the M68HC08. BGND would not be used in
normal user programs because it forces the CPU to stop processing user instructions and enter the active
background mode. The only way to resume execution of the user program is through reset or by a host
debug system issuing a GO, TRACE1, or TAGGO serial command through the background debug
interface.
Software-based breakpoints can be set by replacing an opcode at the desired breakpoint address with the
BGND opcode. When the program reaches this breakpoint address, the CPU is forced to active background
mode rather than continuing the user program.
92
Wait Mode Operation
Stop Mode Operation
BGND Instruction
Modes of Operation
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 1.01
chapter for more details.
Freescale Semiconductor