mc9s08qg8 Freescale Semiconductor, Inc, mc9s08qg8 Datasheet - Page 60
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
mc9s08qg8
Manufacturer Part Number
mc9s08qg8
Description
Hcs08 Microcontrollers
Manufacturer
Freescale Semiconductor, Inc
Datasheet
1.MC9S08QG8.pdf
(300 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
mc9s08qg84CDNE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Company:
Part Number:
mc9s08qg84CDTE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Part Number:
mc9s08qg8CDT
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
mc9s08qg8CDTE
Manufacturer:
ABB
Quantity:
101
Company:
Part Number:
mc9s08qg8CDTE
Manufacturer:
Freescale Semiconductor
Quantity:
41 991
Part Number:
mc9s08qg8CDTE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s08qg8CFFE
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
mc9s08qg8CPBE
Manufacturer:
CYPRESS
Quantity:
310
Chapter 5 Resets, Interrupts, and General System Control
5.5.1
Figure 5-1
points at the next available byte location on the stack. The current values of CPU registers are stored on
the stack starting with the low-order byte of the program counter (PCL) and ending with the CCR. After
stacking, the SP points at the next available location on the stack, which is the address that is one less than
the address where the CCR was saved. The PC value that is stacked is the address of the instruction in the
main program that would have executed next if the interrupt had not occurred.
When an RTI instruction is executed, these values are recovered from the stack in reverse order. As part of
the RTI sequence, the CPU fills the instruction pipeline by reading three bytes of program information,
starting from the PC address recovered from the stack.
The status flag causing the interrupt must be acknowledged (cleared) before returning from the ISR.
Typically, the flag is cleared at the beginning of the ISR so that if another interrupt is generated by this
same source, it will be registered so it can be serviced after completion of the current ISR.
5.5.2
External interrupts are managed by the IRQ status and control register, IRQSC. When the IRQ function is
enabled, synchronous logic monitors the pin for edge-only or edge-and-level events. When the MCU is in
stop mode and system clocks are shut down, a separate asynchronous path is used so the IRQ (if enabled)
can wake the MCU.
5.5.2.1
The IRQ pin enable (IRQPE) control bit in IRQSC must be 1 for the IRQ pin to act as the interrupt request
(IRQ) input. As an IRQ input, the user can choose whether the pin detects edges-only or edges and levels
(IRQMOD), and whether an event causes an interrupt or only sets the IRQF flag, which can be polled by
software.
60
shows the content and organization of a stack frame. Before the interrupt, the stack pointer (SP)
Interrupt Stack Frame
External Interrupt Request Pin (IRQ)
Pin Configuration Options
STACKING
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 1.01
ORDER
UNSTACKING
5
4
3
2
1
ORDER
1
2
3
4
5
Figure 5-1. Interrupt Stack Frame
* High byte (H) of index register is not automatically stacked.
7
INDEX REGISTER (LOW BYTE X)
CONDITION CODE REGISTER
PROGRAM COUNTER HIGH
PROGRAM COUNTER LOW
ACCUMULATOR
TOWARD HIGHER ADDRESSES
TOWARD LOWER ADDRESSES
*
0
SP AFTER
INTERRUPT STACKING
SP BEFORE
THE INTERRUPT
Freescale Semiconductor