mc9s08qg8 Freescale Semiconductor, Inc, mc9s08qg8 Datasheet - Page 32
![no-image](/images/manufacturer_photos/0/2/263/freescale_semiconductor__inc_sml.jpg)
mc9s08qg8
Manufacturer Part Number
mc9s08qg8
Description
Hcs08 Microcontrollers
Manufacturer
Freescale Semiconductor, Inc
Datasheet
1.MC9S08QG8.pdf
(300 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
mc9s08qg84CDNE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Company:
Part Number:
mc9s08qg84CDTE
Manufacturer:
Freescale Semiconductor
Quantity:
135
Part Number:
mc9s08qg8CDT
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
mc9s08qg8CDTE
Manufacturer:
ABB
Quantity:
101
Company:
Part Number:
mc9s08qg8CDTE
Manufacturer:
Freescale Semiconductor
Quantity:
41 991
Part Number:
mc9s08qg8CDTE
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
mc9s08qg8CFFE
Manufacturer:
FREESCALE
Quantity:
20 000
Company:
Part Number:
mc9s08qg8CPBE
Manufacturer:
CYPRESS
Quantity:
310
Chapter 3 Modes of Operation
After entering active background mode, the CPU is held in a suspended state waiting for serial background
commands rather than executing instructions from the user application program.
Background commands are of two types:
The active background mode is used to program a bootloader or user application program into the FLASH
program memory before the MCU is operated in run mode for the first time. When the MC9S08QG8/4 is
shipped from the Freescale factory, the FLASH program memory is erased by default unless specifically
noted, so there is no program that could be executed in run mode until the FLASH memory is initially
programmed. The active background mode can also be used to erase and reprogram the FLASH memory
after it has been previously programmed.
For additional information about the active background mode, refer to the
3.5
Wait mode is entered by executing a WAIT instruction. Upon execution of the WAIT instruction, the CPU
enters a low-power state in which it is not clocked. The I bit in the condition code register (CCR) is cleared
when the CPU enters wait mode, enabling interrupts. When an interrupt request occurs, the CPU exits wait
mode and resumes processing, beginning with the stacking operations leading to the interrupt service
routine.
While the MCU is in wait mode, there are some restrictions on which background debug commands can
be used. Only the BACKGROUND command and memory-access-with-status commands are available
while the MCU is in wait mode. The memory-access-with-status commands do not allow memory access,
but they report an error indicating that the MCU is in either stop or wait mode. The BACKGROUND
command can be used to wake the MCU from wait mode and enter active background mode.
32
•
•
Non-intrusive commands, defined as commands that can be issued while the user program is
running. Non-intrusive commands can be issued through the BKGD pin while the MCU is in run
mode; non-intrusive commands can also be executed when the MCU is in the active background
mode. Non-intrusive commands include:
— Memory access commands
— Memory-access-with-status commands
— BDC register access commands
— The BACKGROUND command
Active background commands, which can only be executed while the MCU is in active background
mode. Active background commands include commands to:
— Read or write CPU registers
— Trace one user program instruction at a time
— Leave active background mode to return to the user application program (GO)
Wait Mode
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 1.01
Development Support
Freescale Semiconductor
chapter.