sed1374 ETC-unknow, sed1374 Datasheet - Page 399
sed1374
Manufacturer Part Number
sed1374
Description
Sed1374 Embedded Memory Color Lcd Controller
Manufacturer
ETC-unknow
Datasheet
1.SED1374.pdf
(420 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
sed137460B5
Manufacturer:
HIROSE
Quantity:
49 000
Company:
Part Number:
sed1374F0A
Manufacturer:
EPSON
Quantity:
650
Company:
Part Number:
sed1374FOA
Manufacturer:
NICHIA
Quantity:
12 000
Part Number:
sed1374FOA
Manufacturer:
EPSON/爱普生
Quantity:
20 000
- Current page: 399 of 420
- Download datasheet (2Mb)
EPSON Research and Development
Vancouver Design Center
2.2 Generic #2 Interface Mode
SDU1374/75-TMPR3912/22U CPU Module
Issue Date: 98/12/23
Generic #2 interface mode is a general and non-processor-specific interface mode on the
SED1374/75. The Generic # 2 interface mode was chosen for this interface due to its
compatibility with the PC Card interface.
The interface requires the following signals:
• BUSCLK is a clock input which synchronizes transfers between the host CPU and the
• The address inputs AB0 through AB15, and the data bus DB0 through DB15, connect
• Chip Select (CS#) is driven by decoding the high-order address lines to select the proper
• WE1# is the high byte enable for both read and write cycles and WE0# is the enable
• RD# is the read enable for the SED1374/75, to be driven low when the host CPU is
• WAIT# is a signal which is output from the SED1374/75 to the host CPU that indicates
• The Bus Status (BS#) and Read/Write (RD/WR#) signals are not used in the bus inter-
SED1374/75. BUSCLK is separate from the input clock (CLKI) and is typically driven
by the host CPU system clock.
directly to the CPU address and data bus, respectively. On 32-bit big endian architec-
tures such as the Power PC, the data bus would connect to the high-order data lines; on
little endian hosts, or 16-bit big endian hosts, they would connect to the low-order data
lines. The hardware engineer must ensure that CNF3 selects the proper endian mode
upon reset.
memory address space.
signal for a write access. These must be generated by external decode hardware based
upon the control outputs from the host CPU.
reading data from the SED1374/75. RD# must be generated by external decode hard-
ware based upon the control outputs from the host CPU.
when data is ready (read cycle) or accepted (write cycle) on the host bus. Since host
CPU accesses to the SED1374/75 may occur asynchronously to the display update, it is
possible that contention may occur in accessing the 1374/75 internal registers and/or
refresh memory. The WAIT# line resolves these contentions by forcing the host to wait
until the resource arbitration is complete. This signal is active low and may need to be
inverted if the host CPU wait state signal is active high.
face for Generic #2 mode. However, BS# is used to configure the SED1374/75 for
Generic #2 mode and must be tied high (connected to IOVDD = 3.3V). RD/WR# must
also be tied high.
X00A-G-004-01
Page 9
Related parts for sed1374
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
SE-BGG729, E-Tec lead free prototype socket drawing for BGG729 and BGG729 packages
Manufacturer:
ACTEL [Actel Corporation]
Datasheet:
Part Number:
Description:
SE-CSG128-H, E-Tec lead free prototype socket drawing for CSG128 and CSG128 packages
Manufacturer:
ACTEL [Actel Corporation]
Datasheet:
Part Number:
Description:
Manufacturer:
ETC-unknow
Datasheet:
Part Number:
Description:
Manufacturer:
ETC-unknow
Datasheet: