cx25870 Conexant Systems, Inc., cx25870 Datasheet - Page 122

no-image

cx25870

Manufacturer Part Number
cx25870
Description
Video Encoder With Adaptive Flicker Filtering And Hdtv Output
Manufacturer
Conexant Systems, Inc.
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
cx25870-14P
Manufacturer:
CONEXANT
Quantity:
20 000
2.0 Internal Registers
2.4 Reading Registers
Table 2-5. Programming Detail For All Read/Write Registers (8 of 16)
2-16
ECCGATE
ECLIP
EN_ASYNC
EN_BLANKO
EN_DOT
EN_OUT
EN_REG_RD
EN_SCART
EN_XCLK
ESTATUS[1:0]
EWSSF1
EWSSF2
Bit/Register
Names
Bit 7–C6
Bit 6–C6
Bit 0–C4
Bits [7:6]–C4
Bit 3–C4
Bit 6–A2
Bit 5–D4
Bit 6–6C
Bit 3–6C
Bit 7–A0
Bit 6–60
Bit 7–60
Bit Location
0 = Normal closed-caption encoding. (DEFAULT)
1 = Enables closed-caption encoding constraints. After encoding, future encoding is
disabled until a complete pair of new data bytes is received. This prevents encoding of
redundant or incomplete data.
0 = Normal operation. (DEFAULT)
1 = Enable clipping; DAC values less than 31 hex are made 31 by the encoder.
0 = Normal operation. (DEFAULT)
1 = Enable asynchronous flicker filer and encoder block timing operation. Use CLKI for
flicker filter and input blocks and PLL for encoder block. Allows for additional clock
ratios between flicker filter and encoder blocks to provide more overscan solutions
similar to the 3:2 clocking mode.
Interface bit: Works in conjunction with EN_DOT, EN_OUT, and SLAVER. Controls
direction of BLANK* signal.
0 = Enables BLANK* as an input.
1 = Enables BLANK* pin as an output, or no BLANK* signal is utilized in the system
interface. (DEFAULT)
Interface bit: Works in conjunction with EN_BLANKO, EN_OUT, and SLAVER. Controls
blanking method.
0 = Encoder uses its internal counters to determine the active-versus-blanked regions of
input data. (DEFAULT)
1 = Encoder uses the BLANK* signal being received to determine where active video
starts (rising edge by default) and where blanking region starts (falling edge by default).
Interface bit: Works in conjunction with EN_BLANKO, EN_DOT, and SLAVER. Turns
timing outputs on or off.
0 = Three-state (CLKO, HSYNC*, VSYNC*, BLANK* and FIELD) timing outputs.
(DEFAULT)
1 = Allows CLKO and other outputs to be enabled (depending upon EN_BLANKO register
bit and the OR combination of the SLAVE pin and the SLAVER bit).
0 = Use ESTATUS[1:0] register to select read back status registers. Enable Bt869-like
Legacy read-back method. (DEFAULT)
1 = Enable Standard serial register read back of all registers.
Enables SCART video output for Europe. OUT_MODE[1:0] field must be set to 11 (VGA
Mode) and HDTV_EN bit must be set to 0.
0 = Enables VGA mode. DACs will output analog RGB with standard bilevel (-40 IRE)
analog syncs (DEFAULT).
1 = Enables SCART output mode. DAC will transmit SCART compatible RGB outputs and
a composite video output which includes an analog sync.
0 = Encoder generates pixel clock. (DEFAULT)
1 = Use CLKI pin as pixel clock source. This bit must be set for slave interface.
Bt868/869 Legacy serial read back status bit selection. Used in conjunction with
EN_REG_RD, CHECK_STAT, and AUTO_CHK. Review
0 = Disable field 1 WSS data. (DEFAULT)
1 = Enable field 1 WSS data.
0 = Disable field 2 WSS data. (DEFAULT)
1 = Enable field 2 WSS data (525 line only).
Conexant
Flicker-Free Video Encoder with Ultrascale Technology
Bit/Register Definition
Table
1-30.
CX25870/871
100381B

Related parts for cx25870