LPC3130FET180,551 NXP Semiconductors, LPC3130FET180,551 Datasheet - Page 26

• Manufacturer Part Number: LPC3130FET180,551
• Description: IC ARM9 MCU 180MHZ 180-TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC3000r

Specifications of LPC3130FET180,551

• Package / Case: 180-TFBGA
• Core Processor: ARM9
• Core Size: 32-Bit
• Speed: 180MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, UART/USART, USB OTG
• Peripherals: DMA, I²S, LCD, PWM, WDT
• Program Memory Type: ROMless
• Ram Size: 96K x 8
• Voltage - Supply (vcc/vdd): 1.1 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC31
• Core: ARM926EJ-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 96 KB
• Interface Type: I2C/I2S/UART/USB
• Maximum Clock Frequency: 180 MHz
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Cpu Family: LPC3000
• Device Core: ARM926EJ-S
• Device Core Size: 16/32Bit
• Frequency (max): 180MHz
• Program Memory Size: Not Required
• Total Internal Ram Size: 96KB
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 1.2/1.8/2.8/3.3/5V
• Operating Supply Voltage (max): 1.3/3.6V
• Operating Supply Voltage (min): 1/1.1/1.65/2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 180
• Package Type: TFBGA
• Package: 180TFBGA
• Family Name: LPC3000
• Maximum Speed: 180 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-4850 - KIT EVAL FOR LPC313X568-4062 - DEBUGGER J-LINK JTAG568-4061 - DEBUGGER U-LINK2 JTAG FOR NXP
• Number Of I /o: -
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4696; 935288013551; LPC3130FET180-S

NXP Semiconductors
LPC3130_3131
Preliminary data sheet
6.17 Input/Output configuration module (IOCONFIG)
6.18 10-bit Analog-to-Digital Converter (ADC10B)
The General Purpose Input/Output (GPIO) pins can be controlled through the register
interface provided in the IOCONFIG module. Next to several dedicated GPIO pins, most
digital I/O pins can also be used as GPIO if they are not required for their normal,
dedicated function.
This module has the following features:
This module is a 10-bit successive approximation Analog-to-Digital Converter (ADC) with
an input multiplexer to allow for multiple analog signals on its input. A common use of this
module is to read out multiple keys on one input from a resistor network.
This module has the following features:
Fig 7. Block diagram of the Watchdog timer
•
•
•
•
•
•
•
•
•
Provides control for the digital pins that can double as GPIO (next to their normal
function). The pinning list in
Each pin controlled by the IOCONFIG can be configured for four operational modes:
– Normal operation (i.e. controlled by a function block).
– Driven LOW.
– Driven HIGH.
– High impedance/input.
The GPIO pins can be observed (read) in any mode.
The register interface provides set and clear access methods for choosing the
operational mode.
Four analog input channels, selected by an analog multiplexer.
Programmable ADC resolution from 2 bit to 10 bit.
The maximum conversion rate is 400 ksample/s for 10 bit resolution and
1500 ksample/s for 2 bit resolution.
Single A/D conversion scan mode and continuous A/D conversion scan mode.
Power-down mode.
APB
All information provided in this document is subject to legal disclaimers.
Rev. 1.04 — 27 May 2010
WDT
m0
m1
Table 4
Low-cost, low-power ARM926EJ-S microcontrollers
EVENT ROUTER
indicates which pins can double as GPIO.
CGU
reset
CONTROLLER
LPC3130/3131
INTERRUPT
002aae086
© NXP B.V. 2010. All rights reserved.
FIQ
IRQ
26 of 72