UPSD3433E-40T6 STMicroelectronics, UPSD3433E-40T6 Datasheet - Page 98

• Manufacturer Part Number: UPSD3433E-40T6
• Description: MCU 8BIT 8032 128KB FLASH 52TQFP
• Manufacturer: STMicroelectronics
• Series: µPSDr

Specifications of UPSD3433E-40T6

• Core Processor: 8032
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, IrDA, SPI, UART/USART, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 160KB (160K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 52-TQFP, 52-VQFP
• For Use With: 497-5518 - EVAL BOARD RFID READER
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: 497-4906

Standard 8032 timer/counters
20.4
20.5
20.5.1
20.5.2
20.5.3
20.5.4
98/300
SFR, TMOD
Timer 0 and Timer 1 have four modes of operation controlled by the SFR named TMOD
(Table
Timer 0 and Timer 1 operating modes
The “Timer” or “Counter” function is selected by the C/T control bits in TMOD. The four
operating modes are selected by bit-pairs M[1:0] in TMOD. Modes 0, 1, and 2 are the same
for both Timer/Counters. Mode 3 is different.
Mode 0
Putting either Timer/Counter into Mode 0 makes it an 8-bit Counter with a divide-by-32 pre-
scaler.
In this mode, the Timer register is configured as a 13-bit register. As the count rolls over
from all '1s' to all '0s,' it sets the Timer Interrupt flag TF1. The counted input is enabled to the
Timer when TR1 = 1 and either GATE = 0 or EXTINT1 = 1. (Setting GATE = 1 allows the
Timer to be controlled by external input pin, EXTINT1, to facilitate pulse width
measurements). TR1 is a control bit in the SFR, TCON. GATE is a bit in the SFR, TMOD.
The 13-bit register consists of all 8 bits of TH1 and the lower 5 bits of TL1. The upper 3 bits
of TL1 are indeterminate and should be ignored. Setting the run flag, TR1, does not clear
the registers.
Mode 0 operation is the same for the Timer 0 as for Timer 1. Substitute TR0, TF0, C0, TL0,
TH0, and EXTINT0 for the corresponding Timer 1 signals in
different GATE Bits, one for Timer 1 and one for Timer 0.
Mode 1
Mode 1 is the same as Mode 0, except that the Timer register is being run with all 16 bits.
Mode 2
Mode 2 configures the Timer register as an 8-bit Counter (TL1) with automatic reload, as
shown in
with the contents of TH1, which is preset with firmware. The reload leaves TH1 unchanged.
Mode 2 operation is the same for Timer/Counter 0.
Mode 3
Timer 1 in Mode 3 simply holds its count. The effect is the same as setting TR1 = 0.
Timer 0 in Mode 3 establishes TL0 and TH0 as two separate counters. The logic for Mode 3
on Timer 0 is shown in
GATE, TR0, and TF0, as well as the pin EXTINT0. TH0 is locked into a timer function
(counting at a rate of 1/12 f
TH0 now controls the “Timer 1“ interrupt flag.
Mode 3 is provided for applications requiring an extra 8-bit timer on the counter (see
Figure 26 on page
three Timer/Counters (not including the PCA). When Timer 0 is in Mode 3, Timer 1 can be
58).
Figure 24
Figure 25 on page
shows Mode 0 operation as it applies to Timer 1 (same applies to Timer 0).
100). With Timer 0 in Mode 3, a UPSD34xx device can look like it has
Figure 26 on page
OSC
100. Overflow from TL1 not only sets TF1, but also reloads TL1
) and takes over the use of TR1 and TF1 from Timer 1. Thus,
100. TL0 uses the Timer 0 control Bits: C/T,
UPSD3422, UPSD3433, UPSD3434, UPSD3454
Figure
24. There are two