P89LPC932A1FA NXP Semiconductors, P89LPC932A1FA Datasheet - Page 31

• Manufacturer Part Number: P89LPC932A1FA
• Description: MCU 8-Bit 89LP 80C51 CISC 8KB Flash 2.5V/3.3V 28-Pin PLCC Tube
• Manufacturer: NXP Semiconductors

Specifications of P89LPC932A1FA

• Package: 28PLCC
• Device Core: 80C51
• Family Name: 89LP
• Maximum Speed: 18 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 26
• Interface Type: I2C/SPI/UART
• Number Of Timers: 2
• Ram Size: 768 Byte
• Program Memory Size: 8 KB
• Program Memory Type: Flash
• Operating Temperature: -40 to 85 °C

NXP Semiconductors
P89LPC932A1_3
Product data sheet
7.20.3 Mode 2
7.20.4 Mode 3
7.20.5 Baud rate generator and selection
7.20.6 Framing error
7.20.7 Break detect
11 bits are transmitted (through TXD) or received (through RXD): start bit (logic 0), 8 data
bits (LSB first), a programmable 9
transmitted, the 9
Or, for example, the parity bit (P, in the PSW) could be moved into TB8. When data is
received, the 9
bit is not saved. The baud rate is programmable to either
frequency, as determined by the SMOD1 bit in PCON.
11 bits are transmitted (through TXD) or received (through RXD): a start bit (logic 0), 8
data bits (LSB first), a programmable 9
the same as Mode 2 in all respects except baud rate. The baud rate in Mode 3 is variable
and is determined by the Timer 1 overflow rate or the Baud Rate Generator (described in
Section 7.20.5 “Baud rate generator and
The P89LPC932A1 enhanced UART has an independent Baud Rate Generator. The baud
rate is determined by a baud-rate preprogrammed into the BRGR1 and BRGR0 SFRs
which together form a 16-bit baud rate divisor value that works in a similar manner as
Timer 1 but is much more accurate. If the baud rate generator is used, Timer 1 can be
used for other timing functions.
The UART can use either Timer 1 or the baud rate generator output (see
that Timer T1 is further divided by 2 if the SMOD1 bit (PCON.7) is cleared. The
independent Baud Rate Generator uses OSCCLK.
Framing error is reported in the status register (SSTAT). In addition, if SMOD0 (PCON.6)
is logic 1, framing errors can be made available in SCON.7 respectively. If SMOD0 is
logic 0, SCON.7 is SM0. It is recommended that SM0 and SM1 (SCON.7:6) are set up
when SMOD0 is logic 0.
Break detect is reported in the status register (SSTAT). A break is detected when
11 consecutive bits are sensed LOW. The break detect can be used to reset the device
and force the device into ISP mode.
Fig 13. Baud rate sources for UART (Modes 1, 3)
baud rate generator
timer 1 overflow
(CCLK-based)
(PCLK-based)
th
data bit goes into RB8 in Special Function Register SCON, while the stop
th
data bit (TB8 in SCON) can be assigned the value of logic 0 or logic 1.
Rev. 03 — 12 March 2007
8-bit microcontroller with accelerated two-clock 80C51 core
2
th
SMOD1 = 1
SMOD1 = 0
data bit, and a stop bit (logic 1). When data is
th
data bit, and a stop bit (logic 1). In fact, Mode 3 is
selection”).
SBRGS = 0
SBRGS = 1
1
16
P89LPC932A1
or
baud rate modes 1 and 3
1
32
of the CPU clock
© NXP B.V. 2007. All rights reserved.
Figure
002aaa897
13). Note
31 of 64