P89LPC932A1FA NXP Semiconductors, P89LPC932A1FA Datasheet - Page 42

• Manufacturer Part Number: P89LPC932A1FA
• Description: MCU 8-Bit 89LP 80C51 CISC 8KB Flash 2.5V/3.3V 28-Pin PLCC Tube
• Manufacturer: NXP Semiconductors

Specifications of P89LPC932A1FA

• Package: 28PLCC
• Device Core: 80C51
• Family Name: 89LP
• Maximum Speed: 18 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 26
• Interface Type: I2C/SPI/UART
• Number Of Timers: 2
• Ram Size: 768 Byte
• Program Memory Size: 8 KB
• Program Memory Type: Flash
• Operating Temperature: -40 to 85 °C

NXP Semiconductors
P89LPC932A1_3
Product data sheet
7.28.3 Flash organization
7.28.4 Using flash as data storage
7.28.5 Flash programming and erasing
7.28.6 In-circuit programming
7.28.7 In-application programming
The program memory consists of eight 1 kB sectors on the P89LPC932A1 device. Each
sector can be further divided into 64-byte pages. In addition to sector erase, page erase,
and byte erase, a 64-byte page register is included which allows from 1 byte to 64 bytes of
a given page to be programmed at the same time, substantially reducing overall
programming time.
The flash code memory array of this device supports individual byte erasing and
programming. Any byte in the code memory array may be read using the MOVC
instruction, provided that the sector containing the byte has not been secured (a MOVC
instruction is not allowed to read code memory contents of a secured sector). Thus any
byte in a non-secured sector may be used for non-volatile data storage.
Four different methods of erasing or programming of the flash are available. The flash may
be programmed or erased in the end-user application (IAP) under control of the
application’s firmware. Another option is to use the ICP mechanism. This ICP system
provides for programming through a serial clock - serial data interface. As shipped from
the factory, the upper 512 bytes of user code space contains a serial ISP routine allowing
for the device to be programmed in circuit through the serial port. The flash may also be
programmed or erased using a commercially available EPROM programmer which
supports this device. This device does not provide for direct verification of code memory
contents. Instead, this device provides a 32-bit CRC result on either a sector or the entire
user code space.
ICP is performed without removing the microcontroller from the system. The ICP facility
consists of internal hardware resources to facilitate remote programming of the
P89LPC932A1 through a two-wire serial interface. The ICP facility has made ICP in an
embedded application—using commercially available programmers—possible with a
minimum of additional expense in components and circuit board area. The ICP function
uses five pins. Only a small connector needs to be available to interface your application
to a commercial programmer in order to use this feature. Additional details may be found
in the P89LPC932A1 User manual .
IAP is performed in the application under the control of the microcontroller’s firmware. The
IAP facility consists of internal hardware resources to facilitate programming and erasing.
The IAP facility has made IAP in an embedded application possible without additional
components. Two methods are available to accomplish IAP. A set of predefined IAP
functions are provided in a Boot ROM and can be called through a common interface,
PGM_MTP. Several IAP calls are available for use by an application program to permit
selective erasing and programming of flash sectors, pages, security bits, configuration
bytes, and device ID. These functions are selected by setting up the microcontroller’s
registers before making a call to PGM_MTP at FF00H. The Boot ROM occupies the
program memory space at the top of the address space from FF00H to FEFFH, thereby
not conflicting with the user program memory space.
Rev. 03 — 12 March 2007
8-bit microcontroller with accelerated two-clock 80C51 core
P89LPC932A1
© NXP B.V. 2007. All rights reserved.
42 of 64