SC16C850VIBS,128 NXP Semiconductors, SC16C850VIBS,128 Datasheet - Page 15

• Manufacturer Part Number: SC16C850VIBS,128
• Description: IC UART SINGLE W/FIFO 32-HVQFN
• Manufacturer: NXP Semiconductors

Specifications of SC16C850VIBS,128

• Features: Programmable
• Number Of Channels: 1, UART
• Fifo's: 128 Byte
• Protocol: RS485
• Voltage - Supply: 1.8V
• With Auto Flow Control: Yes
• With Irda Encoder/decoder: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 32-VFQFN Exposed Pad
• Transmitter And Receiver Fifo Counter: Yes
• Data Rate: 5Mbps
• Mounting: Surface Mount
• Pin Count: 32
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935283087128; SC16C850VIBS-F; SC16C850VIBS-F

NXP Semiconductors
SC16C850V
Product data sheet
6.11.1 Conditions to enter Sleep mode
6.11.2 Conditions to resume normal operation
6.12 Low power feature
6.11 Sleep mode
Sleep mode is an enhanced feature of the SC16C850V UART. It is enabled when EFR[4],
the enhanced functions bit, is set and when IER[4] bit is also set.
Sleep mode is entered when:
In Sleep mode, the UART clock and baud rate clock are stopped. Since most registers are
clocked using these clocks, the power consumption is greatly reduced.
Remark: Writing to the divisor latches, DLL and DLM, to set the baud clock, must not be
done during Sleep mode. Therefore, it is advisable to disable Sleep mode using IER[4]
before writing to DLL or DLM.
SC16C850V resumes normal operation by any of the following:
If the device is awakened by one of the conditions described above, it will return to the
Sleep mode automatically after all the conditions described in
device will stay in Sleep mode until it is disabled by setting any channel’s IER bit 4 to a
logic 0.
When the SC16C850V is in Sleep mode and the host interface bus (AD7 to AD0, IOW,
IOR, CS) remains in steady state, either HIGH or LOW, the sleep current will be in the
microampere range as specified in
is toggling or floating then the sleep current will be higher.
A low power feature is provided by the SC16C850V to prevent the switching of the host
data bus from influencing the sleep current. When the pin LOWPWR is activated (logic
HIGH), the device immediately and unconditionally goes into Low Power mode. All clocks
are stopped and most host interface pins are isolated to reduce power consumption. The
device only returns to normal mode when the LOWPWR pin is de-asserted. The pin can
be left unconnected because it has an internal pull-down resistor.
•
•
•
•
•
•
•
•
Modem input pins are not toggling.
The serial data input line, RX, is idle for 4 character time (logic HIGH) and AFCR1[4]
is 0. When AFCR1[4] is 1, the device will go to sleep regardless of the state of the RX
pin (see
The TX FIFO and TX shift register are empty.
There are no interrupts pending.
The RX FIFO is empty.
Receives a start bit on RX pin.
Data is loaded into transmit FIFO.
A change of state on any of the modem input pins.
Section 7.21
Single UART with 128-byte FIFOs, IrDA, and XScale VLIO bus interface
All information provided in this document is subject to legal disclaimers.
Rev. 5 — 19 January 2011
for the description of AFCR1 bit 4).
Table 36 “Static
characteristics”. If any of these signals
Section 6.11.1
SC16C850V
© NXP B.V. 2011. All rights reserved.
are met. The
15 of 48