ATmega165P Atmel Corporation, ATmega165P Datasheet - Page 74

• Manufacturer Part Number: ATmega165P
• Manufacturer: Atmel Corporation

Specifications of ATmega165P

• Flash (kbytes): 16 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8019K–AVR–11/10
• XCK/AIN0/PCINT2 – Port E, Bit 2
XCK, USART External Clock. The Data Direction Register (DDE2) controls whether the clock is
output (DDE2 set) or input (DDE2 cleared). The XCK pin is active only when the USART oper-
ates in synchronous mode.
AIN0 – Analog Comparator Positive input. This pin is directly connected to the positive input of
the Analog Comparator.
PCINT2, Pin Change Interrupt Source 2: The PE2 pin can serve as an external interrupt source.
• TXD/PCINT1 – Port E, Bit 1
TXD0, UART0 Transmit pin.
PCINT1, Pin Change Interrupt Source 1: The PE1 pin can serve as an external interrupt source.
• RXD/PCINT0 – Port E, Bit 0
RXD, USART Receive pin. Receive Data (Data input pin for the USART). When the USART
Receiver is enabled this pin is configured as an input regardless of the value of DDE0. When the
USART forces this pin to be an input, a logical one in PORTE0 will turn on the internal pull-up.
PCINT0, Pin Change Interrupt Source 0: The PE0 pin can serve as an external interrupt source.
Table 12-9
signals shown in
Table 12-9.
Note:
Signal
Name
PUOE
PUOV
DDOE
DDOV
PVOE
PVOV
PTOE
DIEOE
DIEOV
DI
AIO
1. CKOUT is one if the CKOUT Fuse is programmed.
and
PE7/PCINT7
0
0
CKOUT
1
CKOUT
clk
–
PCINT7 • PCIE0
1
PCINT7 INPUT
–
Overriding Signals for Alternate Functions PE7:PE4
I/O
Table 12-10 on page 75
Figure 12-5 on page
(1)
(1)
PE6/DO/
PCINT6
0
0
0
0
USI_THREE-
WIRE
DO
–
PCINT6 • PCIE0
1
PCINT6 INPUT
–
67.
relates the alternate functions of Port E to the overriding
PE5/DI/SDA/
PCINT5
USI_TWO-WIRE
0
USI_TWO-WIRE
(SDA + PORTE5) •
DDE5
USI_TWO-WIRE •
DDE5
0
0
(PCINT5 • PCIE0) +
USISIE
1
DI/SDA INPUT
PCINT5 INPUT
–
ATmega165P
PE4/USCK/SCL/
PCINT4
USI_TWO-WIRE
0
USI_TWO-WIRE
(USI_SCL_HOLD •
PORTE4) + DDE4
USI_TWO-WIRE • DDE4
0
USITC
(PCINT4 • PCIE0) +
USISIE
1
USCKL/SCL INPUT
PCINT4 INPUT
–
74