ISL6565ACBZ Intersil, ISL6565ACBZ Datasheet - Page 13

• Manufacturer Part Number: ISL6565ACBZ
• Description: IC CTRLR PWM MULTIPHASE 28-SOIC
• Manufacturer: Intersil

Specifications of ISL6565ACBZ

• Pwm Type: Voltage Mode
• Number Of Outputs: 1
• Frequency - Max: 1.5MHz
• Duty Cycle: 66.7%
• Voltage - Supply: 4.75 V ~ 5.25 V
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: 0°C ~ 105°C
• Package / Case: 28-SOIC (7.5mm Width)
• Frequency-max: 1.5MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The filtered error signal modifies the pulse width
commanded by V
I
correction is applied to each active channel.
Channel-current balance is essential in realizing the thermal
advantage of multi-phase operation. The heat generated in
conversion is dissipated over multiple devices and a large
area. The designer avoids the complexity of driving multiple
parallel MOSFETs, and the expense of using heat sinks and
non-standard magnetic materials.
Voltage Regulation
The integrating compensation network shown in Figure 7
insures that the steady-state error in the output voltage is
limited only to the error in the reference voltage (output of
the DAC) and offset errors in the OFS current source,
remote-sense and error amplifiers. Intersil specifies the
guaranteed tolerance of the ISL6565A, ISL6565B to include
the combined tolerances of each of these elements.
The output of the error amplifier, V
sawtooth waveform to generate the PWM signals. The PWM
signals control the timing of the Intersil MOSFET drivers and
regulate the converter output to the specified reference
voltage. The internal and external circuitry that controls
voltage regulation is illustrated in Figure 7.
The ISL6565 incorporates an internal differential remote-
sense amplifier in the feedback path. The amplifier removes
the voltage error encountered when measuring the output
voltage relative to the controller ground reference point
resulting in a more accurate means of sensing output
voltage. Connect the microprocessor sense pins to the non-
inverting input, VSEN, and inverting input, RGND, of the
remote-sense amplifier. The remote-sense output, V
connected to the inverting input of the error amplifier through
an external resistor.
ER
FIGURE 6. CHANNEL-1 PWM FUNCTION AND CURRENT-
toward zero. The same method for error signal
V
COMP
FILTER
BALANCE ADJUSTMENT
NOTE: *CHANNEL 3 IS OPTIONAL.
+
I
ER
COMP
-
+
f(s)
I
1
-
I
AVG
to correct any unbalance and force
SAWTOOTH SIGNAL
13
÷ N
COMP
+
-
, is compared to the
Σ
PWM1
I
I
ISL6565A, ISL6565B
2
3
*
DIFF
, is
A digital to analog converter (DAC) generates a reference
voltage based on the state of logic signals at pins VID4
through VID12.5. The DAC decodes the 6-bit logic signal
(VID) into one of the discrete voltages shown in Table 1.
Each VID input offers a 20µA pull-up to an internal 2.5V
source for use with open-drain outputs. The pull-up current
diminishes to zero above the logic threshold to protect
voltage-sensitive output devices. External pull-up resistors
can augment the pull-up current sources in case leakage
into the driving device is greater than 20µA.
FIGURE 7. OUTPUT VOLTAGE AND LOAD-LINE
R
FB
EXTERNAL CIRCUIT
V
V
+
OUT
OUT
-
V
DROOP
R
-
+
C
REGULATION WITH OFFSET ADUJUSTMENT
R
TCOMP
C
C
C
REF
RGND
COMP
VDIFF
VSEN
REF
FB
ISL6565 INTERNAL CIRCUIT
1k
VID DAC
I
AVG
ERROR AMPLIFIER
DIFFERENTIAL
REMOTE-SENSE
AMPLIFIER
+
-
+
-
December 1, 2005
V
COMP
FN9135.4