DK-DEV-4SE530N Altera, DK-DEV-4SE530N Datasheet - Page 49

• Manufacturer Part Number: DK-DEV-4SE530N
• Description: KIT DEV STRATIX IV FPGA 4SE530
• Manufacturer: Altera
• Series: Stratix® IVr
• Type: FPGAr

Specifications of DK-DEV-4SE530N

• Contents: Board, Cables, CD, DVD, Power Supply
• Silicon Manufacturer: Altera
• Core Architecture: FPGA
• Core Sub-architecture: Stratix
• Silicon Core Number: EP4S
• Silicon Family Name: Stratix IV E
• Rohs Compliant: Yes
• For Use With/related Products: EP4SE530
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 544-2605

Appendix A: Programming the Flash Memory Device
Programming Flash Memory Using the Board Update Portal
Programming Flash Memory Using the Board Update Portal
Programming Flash Memory Using the Nios II EDS
© May 2010 Altera Corporation
1
Once you have the necessary .flash files, you can use the Board Update Portal to
reprogram the flash memory. Refer to
Designs” on page 5–2
If you have generated a .sof that operates without a software design file, you can still
use the Board Update Portal to upload your design. In this case, leave the Software
File Name field blank.
The Nios II EDS offers a nios2-flash-programmer utility to program the flash memory
directly. To program the .flash files or any compatible S-Record File (.srec) to the
board using nios2-flash-programmer, perform the following steps:
1. Set the PGM CONFIG SELECT rotary switch (SW5) to the 0 position to load the
2. Attach the USB-Blaster cable and power up the board.
3. If the board has powered up and the LCD displays either "Connecting..." or a valid
4. Launch the Quartus II Programmer to configure the FPGA with a .sof capable of
5. Click Add File and select <install
6. Turn on the Program/Configure option for the added file.
7. Click Start to download the selected configuration file to the FPGA. Configuration
8. On the Windows Start menu, click All Programs > Altera > Nios II EDS > Nios II
9. In the Nios II command shell, navigate to the <install
nios2-flash-programmer --base=0x08000000 <yourfile>_hw.flash r
10. After programming completes, if you have a software file to program, type the
nios2-flash-programmer --base=0x0A000000 <yourfile>_sw.flash r
11. Set the PGM CONFIG SELECT rotary switch (SW5) to the 1 position and power
Board Update Portal design from flash memory on power up.
IP address (such as 152.198.231.75), proceed to step 8. If no output appears on the
LCD or if the CONF DONE LED (D22) does not illuminate, continue to step 4 to
load the FPGA with a flash-writing design.
flash programming. Refer to
Programmer” on page 6–20
dir>\kits\stratixIVE_4se530_fpga\factory_recovery\s4e530_fpga_bup.sof.
is complete when the progress bar reaches 100%. The CONF DONE LED (D22)
and the eight user LEDs (D23-D30) illuminate indicating that the flash device is
ready for programming.
Command Shell.
dir>\kits\stratixIVE_4se530_fpga\factory_recovery directory (or to the directory
of the .flash files you created in
page
following Nios II EDS command:
cycle the board, or press the RESET CONFIGn button (S1) to load and run the user
hardware design.
A–2) and type the following Nios II EDS command:
for more information.
for more information.
“Configuring the FPGA Using the Quartus II
“Creating Flash Files Using the Nios II EDS” on
“Using the Board Update Portal to Update User
Stratix IV E FPGA Development Kit User Guide
A–3