MC908GZ60CFJE Freescale Semiconductor, MC908GZ60CFJE Datasheet - Page 225

• Manufacturer Part Number: MC908GZ60CFJE
• Description: IC MCU 60K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ60CFJE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: CAN, ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

15.3 Reset and System Initialization
The MCU has these reset sources:
All of these resets produce the vector $FFFE:$FFFF ($FEFE:$FEFF in monitor mode) and assert the
internal reset signal (IRST). IRST causes all registers to be returned to their default values and all
modules to be returned to their reset states.
An internal reset clears the SIM counter (see
the resets sets a corresponding bit in the SIM reset status register (SRSR). See
A reset immediately stops the operation of the instruction being executed. Reset initializes certain control
and status bits. Reset selects CGMXCLK divided by four as the bus clock.
15.3.1 External Pin Reset
The RST pin circuit includes an internal pullup device. Pulling the asynchronous RST pin low halts all
processing. The PIN bit of the SIM reset status register (SRSR) is set as long as RST is held low for at
least the minimum t
15.3.2 Active Resets from Internal Sources
All internal reset sources actively pull the RST pin low for 32 CGMXCLK cycles to allow resetting of
external peripherals. The internal reset continues to be asserted for an additional 32 cycles at which point
the reset vector will be fetched. See
illegal opcode, COP timeout, LVI, or POR. See
The COP reset is asynchronous to the bus clock.
The active reset feature allows the part to issue a reset to peripherals and other chips within a system
built around the MCU.
Freescale Semiconductor
•
•
•
•
•
•
•
Power-on reset module (POR)
External reset pin (RST)
Computer operating properly module (COP)
Low-voltage inhibit module (LVI)
Illegal opcode
Illegal address
Forced monitor mode entry reset (MODRST)
CGMOUT
RST
IAB
For LVI or POR resets, the SIM cycles through 4096 CGMXCLK cycles
during which the SIM forces the RST pin low. The internal reset signal then
follows the sequence from the falling edge of RST shown in
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 Data Sheet, Rev. 6
RL
PC
time and no other reset sources are present.
Figure 15-4. External Reset Timing
Figure
15-5. An internal reset can be caused by an illegal address,
15.4 SIM
Figure
NOTE
15-6.
Counter), but an external reset does not. Each of
VECT H
Figure 15-4
VECT L
Figure
Reset and System Initialization
shows the relative timing.
15.7 SIM Registers.
15-5.
225