MC908GZ60CFJE Freescale Semiconductor, MC908GZ60CFJE Datasheet - Page 55

• Manufacturer Part Number: MC908GZ60CFJE
• Description: IC MCU 60K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GZ60CFJE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 21
• Ram Memory Size: 2KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: CAN, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GZ
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: CAN, ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68EML08GZE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 24 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Decreasing the value in FL2BPR by one increases the protected range by one page (128 bytes).
However, programming the block protect register with $FE protects a range twice that size, 256 bytes, in
the corresponding array. $FE means that locations $7F00–$7FFF are protected in FLASH-2.
The FLASH memory does not exist at some locations. The block protection range configuration is
unaffected if FLASH memory does not exist in that range. Refer to
desired locations are protected.
2.7.3 FLASH-2 Block Protection
Due to the ability of the on-board charge pump to erase and program the FLASH memory in the target
application, provision is made for protecting blocks of memory from unintentional erase or program
operations due to system malfunction. This protection is done by using the FLASH-2 block protection
register (FL2BPR). FL2BPR determines the range of the FLASH-2 memory which is to be protected. The
range of the protected area starts from a location defined by FL2BPR and ends at the bottom of the
FLASH-2 memory ($7FFF). When the memory is protected, the HVEN bit can not be set in either ERASE
or PROGRAM operations.
When the FLASH-2 block protect register is programmed with all 0’s, the entire memory is protected from
being programmed and erased. When all the bits are erased (all 1’s), the entire memory is accessible for
program and erase.
When bits within FL2BPR are programmed (0), they lock a block of memory address ranges as shown in
2.7.2.2 FLASH-2 Block Protect
protected block of FLASH memory can not be erased or programmed.
2.7.4 FLASH-2 Mass Erase Operation
Use this step-by-step procedure to erase the entire FLASH-2 memory:
Freescale Semiconductor
1. Set both the ERASE bit and the MASS bit in the FLASH-2 control register (FL2CR).
2. Read the FLASH-2 block protect register (FL2BPR).
3. Write to any FLASH-2 address within the FLASH-2 array with any data.
4. Wait for a time, t
5. Set the HVEN bit.
6. Wait for a time, t
7. Clear the ERASE and MASS bits.
In performing a program or erase operation, the FLASH-2 block protect
register must be read after setting the PGM or ERASE bit and before
asserting the HVEN bit.
The vector locations and the FLASH block protect registers are located in
the same page. FL1BPR and FL2BPR are not protected with special
hardware or software. Therefore, if this page is not protected by FL1BPR
and the vector locations are erased by either a page or a mass erase
operation, both FL1BPR and FL2BPR will also get erased.
Mass erase is disabled whenever any block is protected (FL2BPR does not
equal $FF).
MC68HC908GZ60 • MC68HC908GZ48 • MC68HC908GZ32 Data Sheet, Rev. 6
NVS
MERASE
(minimum 10 μs).
Register. If FL2BPR is programmed with any value other than $FF, the
(minimum 4 ms).
NOTE
NOTE
NOTE
Figure 2-1
and make sure that the
FLASH-2 Memory (FLASH-2)
55