ATMEGA32U4-AU Atmel, ATMEGA32U4-AU Datasheet - Page 256

• Manufacturer Part Number: ATMEGA32U4-AU
• Description: MCU AVR 32K FLASH 16MHZ 44-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA32U4-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 26
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ATMEGA32x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 2.5 KB
• Interface Type: SPI/TWI/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 16MHz
• Total Internal Ram Size: 2.5KB
• # I/os (max): 26
• Number Of Timers - General Purpose: 5
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: TQFP
• Controller Family/series: AVR MEGA
• No. Of I/o's: 26
• Eeprom Memory Size: 1KB
• Ram Memory Size: 2.5KB
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• For Use With: ATSTK524 - KIT STARTER ATMEGA32M1/MEGA32C1ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ATMEGA32U4-16AU; ATMEGA32U4-16AU

21.4
21.5
7766F–AVR–11/10
Crystal-less operation
Design guidelines
Figure 21-6. Typical Self powered application with 3.0V to 3.6 I/O
To reduce external components count and BOM cost, the USB module can be configured to
operate in low-speed mode with internal RC oscillator as input source clock for the PLL. The
internal RC oscillator is factory calibrated to satisfy the USB low speed frequency accuracy
within the 0°C and -40°C temperature range.
For USB full-speed operation only external crystal oscillator or external source clock can be
used.
• Serial resistors on USB Data lines must have 22 Ohms value (
• Traces from the input USB receptable (or from the cable connection in the case of a tethered
• Voltage transient / ESD suppressors may also be used to prevent USB pads to be damaged
• U
• A 10µF capacitor is highly recommended on VBUS line
device) to the USB microcontroller pads should be as short as possible, and follow differential
traces routing rules (same length, as near as possible, avoid via accumulation).
by external disturbances.
cap
capacitor should be 1µF (
VBUS
UVSS
UDP
UDM
UID
Rs=22
Rs=22
1µF
+/-
10%) for correct operation.
UCAP
VBUS
UGND
D+
D-
UID
UVCC
XTAL1
XTAL2
AVCC
GND
VCC
GND
ATmega16/32U4
+/-
5%).
External 3.0V - 3.6V
Power Supply
256