AT32UC3B0512-Z2UR Atmel, AT32UC3B0512-Z2UR Datasheet - Page 440

• Manufacturer Part Number: AT32UC3B0512-Z2UR
• Description: IC MCU AVR32 512K FLASH 64QFN
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3B0512-Z2UR

• Package / Case: 64-QFN
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 60MHz
• Number Of I /o: 44
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 96K x 8
• Program Memory Size: 512KB (512K x 8)
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Connectivity: I²C, IrDA, SPI, SSC, UART/USART, USB
• Core Size: 32-Bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

•
•
•
•
32059J–12/2010
CURRBK: Current Bank
NBUSYBK: Number of Busy Banks
DTSEQ: Data Toggle Sequence
SHORTPACKET: Short Packet Interrupt
This bit is set for non-control endpoints, to indicate the current bank:
This field may be updated one clock cycle after the RWALL bit changes, so the user should not poll this field as an interrupt bit.
This field is set to indicate the number of busy banks:
For IN endpoints, it indicates the number of banks filled by the user and ready for IN transfer. When all banks are free, this
For OUT endpoints, it indicates the number of banks filled by OUT transactions from the host. When all banks are busy, this
When the FIFOCON bit is cleared (by writing a one to the FIFOCONC bit) to validate a new bank, this field is updated two or
An EPnINT interrupt is triggered if:
- for IN endpoint, NBUSYBKE is one and all the banks are free.
- for OUT endpoint, NBUSYBKE is one and all the banks are busy.
This field is set to indicate the PID of the current bank:
For IN transfers, it indicates the data toggle sequence that will be used for the next packet to be sent. This is not relative to the
For OUT transfers, this value indicates the last data toggle sequence received on the current bank.
By default DTSEQ is 0b01, as if the last data toggle sequence was Data1, so the next sent or expected data toggle sequence
This bit is set for non-control OUT endpoints, when a short packet has been received.
This bit is set for non-control IN endpoints, a short packet is transmitted upon ending a DMA transfer, thus signaling an end of
This triggers an EPnINT interrupt if SHORTPACKETE is one.
This bit is cleared when the SHORTPACKETC bit is written to one. This will acknowledge the interrupt.
0
0
1
1
0
0
1
1
0
0
1
triggers an EPnINT interrupt if NBUSYBKE is one.
triggers an EPnINT interrupt if NBUSYBKE is one.
three clock cycles later to calculate the address of the next bank.
current bank.
should be Data0.
isochronous frame or a bulk or interrupt end of transfer, this only if the End of DMA Buffer Output Enable (DMAENDEN) bit
and the Automatic Switch (AUTOSW) bit are written to one.
NBUSYBK
CURRBK
DTSEQ
X
0
1
0
1
0
1
0
1
0
1
Current Bank
Bank0
Bank1
Bank2
Reserved
Number of Busy Banks
0 (all banks free)
1
2
3
Data Toggle Sequence
Data0
Data1
Reserved
AT32UC3B
440