R5F21217JFP#U1 Renesas Electronics America, R5F21217JFP#U1 Datasheet - Page 341

• Manufacturer Part Number: R5F21217JFP#U1
• Description: MCU FLASH 48K 2.5K CMOS 48LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/2x/21r

Specifications of R5F21217JFP#U1

• Core Processor: R8C
• Core Size: 16/32-Bit
• Speed: 20MHz
• Connectivity: I²C, LIN, SIO, SSU, UART/USART
• Peripherals: POR, Voltage Detect, WDT
• Number Of I /o: 41
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R8C/20 Group, R8C/21 Group
Rev.2.00 Aug 27, 2008
REJ09B0250-0200
16.3.2
Table 16.7
STIE, NAKIE, RIE, TEIE, TIE: Bits in ICIER register
AL, STOP, NACKF, RDRF, TEND, TDRE: Bits in ICSR register
Transmit Data Empty
Transmit Ends
Receive Data Full
Stop Condition Detection
NACK Detection
Arbitration Lost / Overrun Error
The interrupt request of the I
the clock synchronous serial format is used.
Table 16.7 lists the Interrupt Requests of I
Since these interrupt requests are allocated at the I
by each bit is necessary.
When the generation conditions on the Table 16.7 are met, the I
Set the interrupt generation conditions to 0 by the I
TEND bits are automatically set to 0 by writing transmit data to the ICDRT register and the RDRF bit is
automatically set to 0 by reading the ICDRR register. When writing transmit data to the ICDRT register, the
TDRE bit is set to 0. When data is transferred from the ICDRT to ICDRS registers, the TDRE bit is set to 1 and
when further setting the TDRE bit to 0, extra 1 byte may be transmitted.
Also, set the STIE bit to 1 (enable stop condition detection interrupt request) when the STOP bit is set to 0.
Interrupt Requests
Interrupt Request
Interrupt Requests of I
Page 323 of 458
2
C bus interface contains 6 types when the I
NAKI
STPI
RXI
TXI
TEI
2
C Bus Interface
2
C Bus Interface.
TIE = 1 and TDRE = 1
TEIE = 1 and TEND = 1
RIE = 1 and RDRF = 1
STIE = 1 and STOP = 1
NAKIE = 1 and AL = 1 (or
NAKIE = 1 and NACKF = 1)
Generation Condition
2
C bus interface interrupt vector table, determining the source
2
C bus interface interrupt routine. However, the TDRE and
2
C bus interface interrupt request is generated.
16. Clock Synchronous Serial Interface
2
C bus format is used and 4 types when
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
I
2
C bus
Format
Synchronous
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Clock
Serial