ADUC836BSZ Analog Devices Inc, ADUC836BSZ Datasheet - Page 62

• Manufacturer Part Number: ADUC836BSZ
• Description: 16bit Dual ADC With Embedded 8 Bit MCU
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC8xxr

Specifications of ADUC836BSZ

• Core Processor: 8052
• Core Size: 8-Bit
• Speed: 12.58MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: POR, PSM, PWM, Temp Sensor, WDT
• Number Of I /o: 34
• Program Memory Size: 62KB (62K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.25 V
• Data Converters: A/D 7x16b; D/A 1x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 52-MQFP, 52-PQFP
• Cpu Family: ADuC8xx
• Device Core: 8052
• Device Core Size: 8b
• Frequency (max): 12.58MHz
• Interface Type: I2C/SPI/UART
• Total Internal Ram Size: 2.25KB
• # I/os (max): 26
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 2(2-chx16-bit)
• On-chip Dac: 1-chx12-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 52
• Package Type: MQFP
• Package: 52MQFP
• Family Name: ADuC8xx
• Maximum Speed: 12.58 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 26
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Interrupt Priority
The Interrupt Enable registers are written by the user to enable
individual interrupt sources, while the Interrupt Priority registers
allow the user to select one of two priority levels for each inter-
rupt. An interrupt of a high priority may interrupt the service
routine of a low priority interrupt, and if two interrupts of differ-
ent priority occur at the same time, the higher level interrupt will
be serviced first. An interrupt cannot be interrupted by another
interrupt of the same priority level. If two interrupts of the same
priority level occur simultaneously, a polling sequence is used to
determine which interrupt is serviced first. The polling sequence
is shown in Table XXXVIII.
Source
PSMI
WDS
IE0
RDY0/RDY1
TF0
IE1
TF1
ISPI/I2CI
RI + TI
TF2 + EXF2
TII
ADuC836
Table XXXVIII. Priority within an Interrupt Level
Priority
1 (Highest)
2
3
4
5
6
7
8
9
10
11 (Lowest)
Description
Power Supply Monitor Interrupt
Watchdog Interrupt
External Interrupt 0
ADC Interrupt
Timer/Counter 0 Interrupt
External Interrupt 1
Timer/Counter 1 Interrupt
SPI Interrupt
Serial Interrupt
Timer/Counter 2 Interrupt
Time Interval Counter Interrupt
–62–
Interrupt Vectors
When an interrupt occurs, the program counter is pushed onto
the stack and the corresponding interrupt vector address is loaded
into the program counter. The interrupt vector addresses are
shown in Table XXXIX.
*The watchdog can be configured to generate an interrupt instead of
Source
IE0
TF0
IE1
TF1
RI + TI
TF2 + EXF2
RDY0/RDY1 (ADC)
ISPI/I2CI
PSMI
TII
WDS (WDIR = 1)*
a reset when it times out.This is used for logging errors or examining
the internal status of the microcontroller core to understand, from
a software debug point of view, why a watchdog timeout occurred.
The watchdog interrupt is slightly different from the normal inter-
rupts in that its priority level is always set to 1 and it is not possible
to disable the interrupt via the global disable bit (EA) in the IE SFR.
This is done to ensure that the interrupt will always be responded
to if a watchdog timeout occurs. The watchdog will only produce an
interrupt if the watchdog timeout is greater than zero.
Table XXXIX. Interrupt Vector Addresses
Vector Address
0003H
000BH
0013H
001BH
0023H
002BH
0033H
003BH
0043H
0053H
005BH
REV. A