ICS1893YI-10LF IDT, Integrated Device Technology Inc, ICS1893YI-10LF Datasheet - Page 113
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
ICS1893YI-10LF
Manufacturer Part Number
ICS1893YI-10LF
Description
PHYCEIVER LOW PWR 3.3V 64-TQFP
Manufacturer
IDT, Integrated Device Technology Inc
Series
PHYceiver™r
Type
PHY Transceiverr
Specifications of ICS1893YI-10LF
Protocol
MII
Voltage - Supply
3.14 V ~ 3.47 V
Mounting Type
Surface Mount
Package / Case
64-TQFP, 64-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Drivers/receivers
-
Lead Free Status / Rohs Status
Compliant
Other names
1893YI-10LF
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ICS1893YI-10LF
Manufacturer:
IDT
Quantity:
390
Company:
Part Number:
ICS1893YI-10LF
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Part Number:
ICS1893YI-10LF
Manufacturer:
IDT
Quantity:
20 000
Company:
Part Number:
ICS1893YI-10LFT
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
ICS1893 Rev C 6/6/00
Table 9-5.
MDIO
RXCLK
Name
Pin
ICS1893 - Release
Number
MAC/Repeater Interface Pins: Media Independent Interface (MII) (Continued)
Pin
30
38
Output
Output
Input/
Type
Pin
Copyright © 2000, Integrated Circuit Systems, Inc.
All rights reserved.
Management Data Input/Output.
The signal on this pin can be tri-stated and can be driven by one of the
following:
All transfers and sampling are synchronous with the signal on the MDC
pin.
Receive Clock.
The ICS1893 sources the RXCLK to the MAC/repeater interface. The
ICS1893 uses RXCLK to synchronize the signals on the following pins:
RXD[3:0], RXDV, and RXER. The following table contrasts the behavior
on the RXCLK pin when the mode for the ICS1893 is either 10Base-T or
100Base-TX.
Note: If the ICS1893 is to be used in an application that uses the
•
•
Note: The signal on the RXCLK pin is conditioned by the RXTRI pin.
A Station Management Entity (STA), to transfer command and data
information to the registers of the ICS1893.
The ICS1893, to transfer status information.
The RXCLK frequency is 2.5
MHz.
The ICS1893 generates its
RXCLK from the MDI data stream
using a digital PLL. When the MDI
data stream terminates, the PLL
continues to operate,
synchronously referenced to the
last packet received.
The ICS1893 switches between
clock sources during the period
between when its CRS is
asserted and prior to its RXDV
being asserted. While the
ICS1893 is locking onto the
incoming data stream, a clock
phase change of up to 360
degrees can occur.
The RXCLK aligns once per
packet.
mechanical MII specification, MDIO must have a 1.5 k
pull-up resistor at the ICS1893 end and a 2 k ±5% pull-down
resistor at the station management end. (These resistors enable
the station management to determine if the connection is intact.)
10Base-T
113
Chapter 9 Pin Diagram, Listings, and Descriptions
Pin Description
The RXCLK frequency is 25 MHz.
The ICS1893 generates its
RXCLK from the MDI data stream
while there is a valid link (that is,
either data or IDLEs). In the
absence of a link, the ICS1893
uses the REF_IN clock to
generate the RXCLK.
While the ICS1893 is bringing up
a link, a clock phase change of up
to 360 degrees can occur.
The RXCLK aligns once, when
the link is being established.
100Base-TX
±5%
June, 2000