ICS1893YI-10LF IDT, Integrated Device Technology Inc, ICS1893YI-10LF Datasheet - Page 79
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
ICS1893YI-10LF
Manufacturer Part Number
ICS1893YI-10LF
Description
PHYCEIVER LOW PWR 3.3V 64-TQFP
Manufacturer
IDT, Integrated Device Technology Inc
Series
PHYceiver™r
Type
PHY Transceiverr
Specifications of ICS1893YI-10LF
Protocol
MII
Voltage - Supply
3.14 V ~ 3.47 V
Mounting Type
Surface Mount
Package / Case
64-TQFP, 64-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Drivers/receivers
-
Lead Free Status / Rohs Status
Compliant
Other names
1893YI-10LF
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ICS1893YI-10LF
Manufacturer:
IDT
Quantity:
390
Company:
Part Number:
ICS1893YI-10LF
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
Part Number:
ICS1893YI-10LF
Manufacturer:
IDT
Quantity:
20 000
Company:
Part Number:
ICS1893YI-10LFT
Manufacturer:
IDT, Integrated Device Technology Inc
Quantity:
10 000
8.6.5.2
8.6.6 Selector Field (Bits 4.4:0)
ICS1893 Rev C 6/6/00
In Software mode (that is, the HW/SW pin is logic one), these TAF bits are Command Override Write bits.
The default value of these bits depends on the signal level on the HW/SW pin and whether the
Auto-Negotiation sublayer is enabled.
In Software mode, with the Auto-Negotiation Enable bit (bit 0.12) set to logic:
•
•
When its Auto-Negotiation Sublayer is enabled, the ICS1893 transmits its link capabilities to its remote Link
Partner during the auto-negotiation process. The Selector Field is transmitted based on the value of bits
4.4:0. These bits indicate to the remote link partner the type of message being sent during the
auto-negotiation process. The ICS1893 supports IEEE Std 802.3, represented by a value of 00001b in bits
4.4:0. The ISO/IEC 8802-3 standard defines the Selector Field technologies in Annex 28A.
Technology Ability Field: Software Mode
Zero (that is, disabled), the ICS1893 does not execute the auto-negotiation process. Upon completion of
the initialization sequence, the ICS1893 proceeds to the Idle state and begins transmitting IDLES. Two
Control Register bits – the Data Rate Select bit (bit 0.13) and the Duplex Select bit (bit 0.8) – determine
the technology mode that the ICS1893 uses for data transmission and reception. In this mode, the
values of the TAF bits (bits 4.8:5) are undefined.
One (that is, enabled), the ICS1893 executes the auto-negotiation process and advertises its capabilities
to the remote link partner. The TAF bits (bits 4.8:5) determine the capabilities that the ICS1893
advertises to its remote link partner. For the ICS1893, all of these bits 4.8:5 are set to logic one,
indicating the ability of the ICS1893 to provide these technologies.
ICS1893 - Release
Note:
1. The ICS1893 does not alter the value of the Status Register bits based on the TAF bits in register
2. In this mode, an STA can alter the default TAF bit settings, 4.12:5, and subsequently issue an
4, as the ISO/IEC definitions for the Status Register bits require these bits to indicate all the
capabilities of the ICS1893.
Auto-Negotiation Restart.
Copyright © 2000, Integrated Circuit Systems, Inc.
All rights reserved.
79
Chapter 8 Management Register Set
June, 2000