PNX1501E NXP Semiconductors, PNX1501E Datasheet - Page 554

no-image

PNX1501E

Manufacturer Part Number
PNX1501E
Description
Digital Signal Processors & Controllers (DSP, DSC) MEDIA PROCESSOR PNX15XX/266MHZ
Manufacturer
NXP Semiconductors
Datasheet

Specifications of PNX1501E

Product
DSPs
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
SOT-795
Minimum Operating Temperature
0 C
Lead Free Status / Rohs Status
 Details
Other names
PNX1501E,557

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PNX1501E
Manufacturer:
PHILIPS
Quantity:
5
Part Number:
PNX1501E,557
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
PNX1501E/G
Manufacturer:
NXP Semiconductors
Quantity:
135
Part Number:
PNX1501E/G
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
PNX1501E/G
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
Volume 1 of 1
12NC 9397 750 14321
Product data sheet
2.3.4 Bandwidth and Latency Requirements
The format in memory for both little and big-endian byte ordering is shown in
Normally, the rate of transmission of frames corresponds exactly to the source
sampling frequency. The maximum latency requirement will be for 96 kHz streams
(i.e. frame rate = 96 kHz) with the SPDIF Input input set up for any of the 32-bit
capture modes:
(96K frames/sec) x (8bytes/ frame) = 0.768Mbytes/sec
The maximum latency allowed in order to sustain this transfer rate is (assuming data
transfers are 64 bytes each):
64 bytes/N sec= 0.768 Mbytes/sec
Solving for N and providing a relation,
For error-free operation during sustained DMA, there needs to be one 64 byte DMA
write transfer completed to memory every 83 usecs. This guarantees the latency
requirement for the worst case input sample rate. If the latency requirement is not
met, the hardware sets the HBE bit in the SPDI_STATUS register to logic ‘1’
indicating a bandwidth error. For this condition, one or more audio samples have
been lost and are not recoverable. The bus arbitration for the SPDIF Input input block
should be adjusted by the user to satisfy this latency requirement. Refer to section
Section 3.2
N 83.33uSec
Figure 5:
Note: n, n+1, n+2, n+3 refer
to increasing byte addresses
within a naturally aligned 32-bit
memory address. (i.e. n = 0x0,
0x4, 0x8,0xC, etc.)
R: Right
L: Left
for details on SPDI_STATUS and other registers.
Endian Mode Byte Address Memory Format
Rev. 2 — 1 December 2004
16-bit Stereo
16-bit Stereo
32-bit Stereo
32-bit Stereo
or raw
Little Endian
or raw
Big Endian
Little Endian
Big Endian
31
31
31
31
msbyte
lsbyte
n+3
n+3
msbyte
n+3
n+3
lsbyte
R
R
L
L
© Koninklijke Philips Electronics N.V. 2002-2003-2004. All rights reserved.
lsbyte
msbyte
n+2
n+2
lsbyte
msbyte lsbyte
n
n
0
0
PNX15xx Series
15
15
n+7
n+7
msbyte
31
31
Chapter 18: SPDIF Input
n+1
n+1
lsbyte
msbyte
L
L
R
R
msbyte
lsbyte
n
n
n+4
lsbyte
n+4
msbyte
Figure 5
0
0
0
0
etc.
etc.
etc.
etc.
(14)
18-5

Related parts for PNX1501E