lpc4310 NXP Semiconductors, lpc4310 Datasheet - Page 14

• Manufacturer Part Number: lpc4310
• Description: Lpc4350/30/20/10 32-bit Arm Cortex-m4/m0 Mcu; Up To 264 Kb Sram; Ethernet; Two High-speed Usbs; Advanced Configurable Peripherals
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 3.
LPC4350_30_20_10
Objective data sheet
Symbol
P5_7
P6_0
P6_1
P6_2
P6_3
P6_4
P6_5
P6_6
[2]
[2]
[2]
[2]
[2]
[2]
[2]
[2]
Pin description
LBGA256
pin
R12
M12
R15
L13
P15
R16
P16
L14
…continued
Reset
state
I; PU
<tbd>
I; PU
I; PU
I; PU
I; PU
I; PU
I; PU
Type Description
I/O
O
I/O
-
I/O
O
-
-
I/O
O
I/O
I/O
I/O
O
I/O
I/O
I/O
O
I/O
O
I/O
I
O
O
I/O
O
I
O
I/O
O
I/O
O
All information provided in this document is subject to legal disclaimers.
GPIO2[7] — General purpose digital input/output pin.
MCOA2 — Motor control PWM channel 2, output A.
EXTBUS_D11 — External memory data line 11.
n.c.
I2S0_RX_SCK — Receive Clock. It is driven by the master and received by
the slave. Corresponds to the signal SCK in the I
I2S0_RX_MCLK — I2S0 receive master clock.
n.c.
n.c.
GPIO3[0] — General purpose digital input/output pin.
EXTBUS_DYCS1 — SDRAM chip select 1.
U0_UCLK — Serial clock input/output for USART0 in synchronous mode.
I2S0_RX_WS — Receive Word Select. It is driven by the master and
received by the slave. Corresponds to the signal WS in the I
specification.
GPIO3[1] — General purpose digital input/output pin.
EXTBUS_CKEOUT1 — SDRAM clock enable 1.
U0_DIR — RS-485/EIA-485 output enable/direction control for USART0.
I2S0_RX_SDA — I2S0 Receive data. It is driven by the transmitter and read
by the receiver. Corresponds to the signal SD in the I
GPIO3[2] — General purpose digital input/output pin.
USB0_PWR_EN — VBUS drive signal (towards external charge pump or
power management unit); indicates that the VBUS signal must be driven
(active HIGH).
SGPIO4 — General purpose digital input/output pin.
EXTBUS_CS1 — LOW active Chip Select 1 signal.
GPIO3[3] — General purpose digital input/output pin.
CTIN_6 — SCT input 6. Capture input 1 of timer 3.
U0_TXD — Transmitter output for USART0.
EXTBUS_CAS — LOW active SDRAM Column Address Strobe.
GPIO3[4] — General purpose digital input/output pin.
CTOUT_6 — SCT output 6. Match output 2 of timer 1.
U0_RXD — Receiver input for USART0.
EXTBUS_RAS — LOW active SDRAM Row Address Strobe.
GPIO0[5] — General purpose digital input/output pin.
EXTBUS_BLS1 — LOW active Byte Lane select signal 1.
SGPIO5 — General purpose digital input/output pin.
USB0_PWR_FAULT — Port power fault signal indicating overcurrent
condition; this signal monitors over-current on the USB bus (external circuitry
required to detect over-current condition).
Rev. 1 — 29 October 2010
32-bit ARM Cortex-M4/M0 microcontroller
LPC4350/30/20/10
2
S-bus specification.
2
S-bus specification.
© NXP B.V. 2010. All rights reserved.
2
S-bus
14 of 85