lpc4310 NXP Semiconductors, lpc4310 Datasheet - Page 9

• Manufacturer Part Number: lpc4310
• Description: Lpc4350/30/20/10 32-bit Arm Cortex-m4/m0 Mcu; Up To 264 Kb Sram; Ethernet; Two High-speed Usbs; Advanced Configurable Peripherals
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 3.
LPC4350_30_20_10
Objective data sheet
Symbol
P1_19
P1_20
P2_0
P2_1
P2_2
P2_3
P2_4
P2_5
[2]
[2]
[2]
[2]
[2]
[3]
[2]
[2]
Pin description
LBGA256
pin
M11
M10
T16
N15
M15
J12
K11
K14
…continued
Reset
state
<tbd>
I; PU
<tbd>
<tbd>
<tbd>
<tbd>
<tbd>
<tbd>
Type Description
I
I/O
O
I/O
I/O
I/O
-
O
I/O
O
I/O
O
I/O
I
I/O
O
I/O
I/O
I/O
O
I/O
I/O
O
I
I/O
I/O
I
I
I/O
I
I
I
All information provided in this document is subject to legal disclaimers.
ENET_TX_CLK (ENET_REF_CLK) — Ethernet Transmit Clock (MII
interface) or Ethernet Reference Clock (RMII interface).
SSP1_SCK — Serial clock for SSP1.
CLKOUT — Clock output pin.
I2S1_RX_SCK — Receive Clock. It is driven by the master and received by
the slave. Corresponds to the signal SCK in the I
GPIO0[15] — General purpose digital input/output pin.
SSP1_SSEL — Slave Select for SSP1.
n.c.
ENET_TXD1 — Ethernet transmit data 1 (RMII/MII interface).
SGPIO4 — General purpose digital input/output pin.
U0_TXD — Transmitter output for USART0.
EXTBUS_A13 — External memory address line 13.
USB0_PWR_EN — VBUS drive signal (towards external charge pump or
power management unit); indicates that Vbus must be driven (active high).
SGPIO5 — General purpose digital input/output pin.
U0_RXD — Receiver input for USART0.
EXTBUS_A12 — External memory address line 12.
USB0_PWR_FAULT — Port power fault signal indicating overcurrent
condition; this signal monitors over-current on the USB bus (external circuitry
required to detect over-current condition).
SGPIO6 — General purpose digital input/output pin.
U0_UCLK — Serial clock input/output for USART0 in synchronous mode.
EXTBUS_A11 — External memory address line 11.
USB0_IND1 — <tbd>.
SGPIO12 — General purpose digital input/output pin.
I2C1_SDA — I
pad).
U3_TXD — Transmitter output for USART3.
CTIN_1 — SCT input 1. Capture input 1 of timer 0. Capture input 1 of timer
2.
SGPIO13 — General purpose digital input/output pin.
I2C1_SCL — I
pad).
U3_RXD — Receiver input for USART3.
CTIN_0 — SCT input 0. Capture input 0 of timer 0, 1, 2, 3.
SGPIO14 — General purpose digital input/output pin.
CTIN_2 — SCT input 2. Capture input 2 of timer 0.
USB1_VBUS — Monitors the presence of USB1 bus power.
Note: This signal must be HIGH for USB reset to occur.
ADCTRIG1 — ADC trigger input 1.
Rev. 1 — 29 October 2010
2
2
C1 clock input/output (this pin does not use a specialized I
C1 data input/output (this pin does not use a specialized I
32-bit ARM Cortex-M4/M0 microcontroller
LPC4350/30/20/10
2
S-bus specification.
© NXP B.V. 2010. All rights reserved.
9 of 85
2
2
C
C