lpc4310 NXP Semiconductors, lpc4310 Datasheet - Page 20

• Manufacturer Part Number: lpc4310
• Description: Lpc4350/30/20/10 32-bit Arm Cortex-m4/m0 Mcu; Up To 264 Kb Sram; Ethernet; Two High-speed Usbs; Advanced Configurable Peripherals
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 3.
LPC4350_30_20_10
Objective data sheet
Symbol
PC_2
PC_3
PC_4
PC_5
PC_6
PC_7
PC_8
PC_9
PC_10
[2]
[2]
[2]
[2]
[2]
[2]
[2]
[2]
[2]
Pin description
LBGA256
pin
F6
F5
F4
G4
H6
G5
N4
K2
M5
…continued
Reset
state
<tbd>
<tbd>
<tbd>
<tbd>
I; PU
I; PU
<tbd>
I; PU
I; PU
Type Description
I/O
O
I
O
I/O
O
O
O
I/O
I/O
I/O
I
I/O
I/O
I/O
O
I/O
I/O
I/O
I
I/O
I/O
I/O
I
I
I/O
I/O
I
I/O
I
O
I
I/O
O
I
I/O
All information provided in this document is subject to legal disclaimers.
USB1_ULPI_D6 — ULPI link bidirectional data line 6.
SDIO_RST — SDIO reset signal for MMC4.4 card.
U1_CTS — Clear to Send input for UART 1.
ENET_TXD2 — Ethernet transmit data 2 (MII interface).
USB1_ULPI_D5 — ULPI link bidirectional data line 5.
SDIO_VOLT1 — SDIO bus voltage select output 1.
U1_RTS — Request to Send output for UART 1. Can also be configured to
be an RS-485/EIA-485 output enable signal for UART 1.
ENET_TXD3 — Ethernet transmit data 3 (MII interface).
SDIO_D0 — SDIO data bus line 0.
USB1_ULPI_D4 — ULPI link bidirectional data line 4.
SPIFI_CS — SPIFI serial flash chip select.
ENET_COL — Ethernet Collision detect (MII interface).
SDIO_D1 — SDIO data bus line 1.
USB1_ULPI_D3 — ULPI link bidirectional data line 3.
SPIFI_MISO — Input I1 in SPIFI quad mode; SPIFI output IO1.
ENET_TX_ER — Ethernet Transmit Error (MII interface).
GPIO6[0] — General purpose digital input/output pin.
USB1_ULPI_D2 — ULPI link bidirectional data line 2.
SDIO_D2 — SDIO data bus line 2.
ENET_RXD2 — Ethernet receive data 2 (RMII/MII interface).
GPIO6[1] — General purpose digital input/output pin.
USB1_ULPI_D1 — ULPI link bidirectional data line 1.
SDIO_D3 — SDIO data bus line 3.
ENET_RXD3 — Ethernet receive data 3 (RMII/MII interface).
SDIO_CD — SDIO card detect input.
USB1_ULPI_D0 — ULPI link bidirectional data line 0.
SPIFI_SIO2 — I/O lane 2 for SPIFI.
ENET_CRS (ENET_CRS_DV) — Ethernet Carrier Sense (MII interface) or
Ethernet Carrier Sense/Data Valid (RMII interface).
GPIO6[2] — General purpose digital input/output pin.
USB1_ULPI_NXT — ULPI link NXT signal. Data flow control signal from the
PHY.
SDIO_POW — <tbd>.
ENET_RX_ER — Ethernet receive error (RMII/MII interface).
GPIO6[3] — General purpose digital input/output pin.
USB1_ULPI_STP — ULPI link STP signal. Asserted to end or interrupt
transfers to the PHY.
U1_DSR — Data Set Ready input for UART 1.
SDIO_CMD — SDIO command signal.
Rev. 1 — 29 October 2010
32-bit ARM Cortex-M4/M0 microcontroller
LPC4350/30/20/10
© NXP B.V. 2010. All rights reserved.
20 of 85