pxb4219 Infineon Technologies Corporation, pxb4219 Datasheet - Page 67
pxb4219
Manufacturer Part Number
pxb4219
Description
Iwe8 Interworking Element For 8 E1/t1 Lines
Manufacturer
Infineon Technologies Corporation
Datasheet
1.PXB4219.pdf
(290 pages)
- Current page: 67 of 290
- Download datasheet (4Mb)
4.4.2.3
Before a channel is activated, the Reassembly Buffer must be configured properly to
compensate Cell Delay Variation (CDV).
In order to avoid buffer underflow due to large cell distances the amount of initial
starvation octets that are passed to the framer interface upon arrival of the first cell needs
to be set. On the other hand this number needs to be as small as possible to avoid
excessive delay. The logical Reassembly Buffer size can be adjusted in order to detect
too small cell distances by Reassembly Buffer overflow.
All parameters are defined in the “AAL Transmit Reference Slot” in RAM3. The amount
of starvation octets given to the framer transmit interface after arrival of the first cell is
defined by “starv_ini”. The contents of the starvation octets can be defined by
“starv_bpslct” and the logical Reassembly Buffer size can be configured with “buff_lsize”.
The following sections give an overview on the Reassembly Buffer operation and
initialization.
Unstructured Data Transfer:
After activation of a channel both SAR Receiver and Framer Transmit Interface start
operation. As long as no reassembled cell is available in the Reassembly Buffer it is
considered to be in underflow condition and starvation octets are passed to the Framer
Transmit Interface.
As soon as the first reassembled cell is available in the Reassembly Buffer the device
starts building up the Reassembly Buffer threshold level. This is done by passing an
additional amount of starvation octets to the framer Transmit Interface
Figure 15
Data Sheet
Framer
4
0
Interf.
Filling Level [octets]
Reassembly Buffer
buff_lsize
Starvation octets
Data octets
Initialization of the Reassembly Buffer
T
0
Reassembly Buffer Initialization: No CDV
T
0
+T
S
T
T
T: Average cell distance
0
S
: First cell arrival time
: (starv_ini+1) * 125µs / N
T
0
+T
Example:
part_fill = 16 octets
N = 16
no CDV
67
PXB4219 / PXB4220 / PXB4221
Operational Description
T
0
+2*T
2002-05-06
Time
Time
Related parts for pxb4219
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Antenna Switch Silicon Pin Diode
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Silicon Switching Diodes
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Single Igbt Driver Ic
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
5 Volt Standard Regulator
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Active Biased Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Small Signal Mosfet 20v?800v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Sipmos Small-signal Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v Small-signal-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
P-channel Mosfets Power-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Mosfet 20v?300v Power Transistor Power Mosfet
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Power Mosfets
Manufacturer:
Infineon Technologies Corporation
Datasheet: