PCF8811U/2DA/1 NXP [NXP Semiconductors], PCF8811U/2DA/1 Datasheet - Page 34
PCF8811U/2DA/1
Manufacturer Part Number
PCF8811U/2DA/1
Description
80 x 128 pixels matrix LCD driver
Manufacturer
NXP [NXP Semiconductors]
Datasheet
1.PCF8811U2DA1.pdf
(81 pages)
- Current page: 34 of 81
- Download datasheet (441Kb)
NXP Semiconductors
PCF8811_4
Product data sheet
Fig 30. Data transfer timing format in F/S-mode and Hs-mode
SDAH
SCLH
SDAH
SCLH
= Master current source pull-up
= Resistor pull-up
S
t
H
Sr
As no device is allowed to acknowledge the master code, the master code is followed by a
not-acknowledge (A). After this A bit, and the SCLH line pulled up to a HIGH level, the
active master switches to Hs-mode and enables at t
the SCLH signal; see
The active master will then send a repeated START condition (Sr) followed by a 7-bit slave
address (SLA) with a R/W bit, and receives an acknowledge bit (A) from the selected
slave.
After each acknowledge bit (A) or not-acknowledge bit (A) the active master disables its
current source pull-up circuit. The active master re-enables its current source again when
all devices have been released and the SCLH signal reaches a HIGH level. The rising of
the SCLH signal is done by a pull-up resistor and therefore is slower, the last part of the
SCLH rise time is speeded up because the current source is enabled. Data transfer only
switches back to F/S-mode after a STOP condition (P).
A write sequence after the Hs-mode is selected is shown in
initiated with a START condition (S) from the I
address. All slaves with the corresponding address acknowledge in parallel, the remainder
will ignore the I
1
1
2 to 5
7-bit SLA
2
C-bus transfer.
6
2 to 5
7
8-bit master code 0000 1xxx
Figure
Rev. 04 — 27 June 2008
R/W
8
9
30.
A
F/S-mode
Hs-mode
1
6
2 to 5
n + (8-bit data
2
7
C-bus master which is followed by the slave
6
7
H
the current-source pull-up circuit for
+
80 x 128 pixels matrix LCD driver
8
8
A/A)
9
Figure
A
9
Sr P
t
31. The sequence is
FS
t
1
If Sr (dotted lines)
then Hs-mode
If P then
F/S-mode
PCF8811
© NXP B.V. 2008. All rights reserved.
t
H
msc618
34 of 81
Related parts for PCF8811U/2DA/1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: