S912XET512J3VALR Freescale Semiconductor, S912XET512J3VALR Datasheet - Page 780

• Manufacturer Part Number: S912XET512J3VALR
• Description: 16-bit Microcontrollers - MCU 16 BIT,512K FLASH
• Manufacturer: Freescale Semiconductor

Specifications of S912XET512J3VALR

• Rohs: yes
• Core: HCS12X
• Processor Series: MC9S12XE
• Data Bus Width: 16 bit
• Maximum Clock Frequency: 50 MHz
• Program Memory Size: 512 KB
• Data Ram Size: 32 KB
• On-chip Adc: Yes
• Operating Supply Voltage: 3.13 V to 5.5 V
• Operating Temperature Range: - 40 C to + 105 C
• Package / Case: LQFP-112
• Mounting Style: SMD/SMT

Chapter 21 Serial Peripheral Interface (S12SPIV5)
When the third edge occurs, the value previously latched from the serial data input pin is shifted into the
LSB or MSB of the SPI shift register, depending on LSBFE bit. After this edge, the next bit of the master
data is coupled out of the serial data output pin of the master to the serial input pin on the slave.
This process continues for a total of n
edges and shifting taking place on odd numbered edges.
Data reception is double buffered, data is serially shifted into the SPI shift register during the transfer and
is transferred to the parallel SPI data register after the last bit is shifted in.
After 2n
Figure 21-14
slave timing diagram because the SCK, MISO, and MOSI pins are connected directly between the master
and the slave. The MISO signal is the output from the slave, and the MOSI signal is the output from the
master. The SS line is the slave select input to the slave. The SS pin of the master must be either high or
reconfigured as a general-purpose output not affecting the SPI.
780
•
•
End of Idle State
SCK Edge Number
SCK (CPOL = 0)
SCK (CPOL = 1)
SAMPLE I
MOSI/MISO
CHANGE O
CHANGE O
SEL SS (O)
Master only
SEL SS (I)
MOSI pin
MISO pin
Data that was previously in the SPI data register of the master is now in the data register of the
slave, and data that was in the data register of the slave is in the master.
The SPIF flag bit in SPISR is set indicating that the transfer is complete.
Figure 21-14. SPI Clock Format 1 (CPHA = 1), with 8-Bit Transfer Width selected (XFRW = 0)
MSB first (LSBFE = 0):
t
t
t
LSB first (LSBFE = 1):
L
T
I
1
= Minimum idling time between transfers (minimum SS high time), not required for back-to-back transfers
= Minimum leading time before the first SCK edge, not required for back-to-back transfers
= Minimum trailing time after the last SCK edge
SCK edges:
shows two clocking variations for CPHA = 1. The diagram may be interpreted as a master or
t
L
1
MSB
LSB
2
MC9S12XE-Family Reference Manual Rev. 1.25
3
Begin
Bit 6
Bit 1
4
1
edges on the SCK line with data being latched on even numbered
5
Bit 5
Bit 2
6
7
Bit 4
Bit 3
8
Transfer
9
Bit 3
Bit 4
10
11
Bit 2
Bit 5
12
13 14
Bit 1
Bit 6
End
15
MSB
LSB
16
t
T
Minimum 1/2 SCK
Freescale Semiconductor
Begin of Idle State
t
I
for t
T
t
, t
L
l
, t
L