AT90USB1287-AU Atmel, AT90USB1287-AU Datasheet - Page 114

• Manufacturer Part Number: AT90USB1287-AU
• Description: IC AVR MCU 128K 64TQFP
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB1287-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART, USB, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 48
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: AT90USBx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire/SPI/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525, ATAVRQTOUCHX
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Controller Family/series: AVR USB
• No. Of I/o's: 48
• Eeprom Memory Size: 4KB
• Ram Memory Size: 8KB
• Cpu Speed: 20MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: AT90USB1287-16AU; AT90USB1287-16AU

13.8.3
114
AT90USB64/128
Timer/Counter Register – TCNT0
A FOC0A strobe will not generate any interrupt, nor will it clear the timer in CTC mode using
OCR0A as TOP.
The FOC0A bit is always read as zero.
• Bit 6 – FOC0B: Force Output Compare B
The FOC0B bit is only active when the WGM bits specify a non-PWM mode.
However, for ensuring compatibility with future devices, this bit must be set to zero when
TCCR0B is written when operating in PWM mode. When writing a logical one to the FOC0B bit,
an immediate Compare Match is forced on the Waveform Generation unit. The OC0B output is
changed according to its COM0B1:0 bits setting. Note that the FOC0B bit is implemented as a
strobe. Therefore it is the value present in the COM0B1:0 bits that determines the effect of the
forced compare.
A FOC0B strobe will not generate any interrupt, nor will it clear the timer in CTC mode using
OCR0B as TOP.
The FOC0B bit is always read as zero.
• Bits 5:4 – Res: Reserved Bits
These bits are reserved bits and will always read as zero.
• Bit 3 – WGM02: Waveform Generation Mode
See the description in the
• Bits 2:0 – CS02:0: Clock Select
The three Clock Select bits select the clock source to be used by the Timer/Counter.
Table 13-8.
If external pin modes are used for the Timer/Counter0, transitions on the T0 pin will clock the
counter even if the pin is configured as an output. This feature allows software control of the
counting.
Bit
Read/Write
Initial Value
CS02
0
0
0
0
1
1
1
1
CS01
0
0
1
1
0
0
1
1
7
TCNT0[7:0]
R/W
0
Clock Select Bit Description
CS00
0
1
0
1
0
1
0
1
6
R/W
0
Description
No clock source (Timer/Counter stopped)
clk
clk
clk
clk
clk
External clock source on T0 pin. Clock on falling edge.
External clock source on T0 pin. Clock on rising edge.
“Timer/Counter Control Register A – TCCR0A” on page
I/O
I/O
I/O
I/O
I/O
5
R/W
0
/(No prescaling)
/8 (From prescaler)
/64 (From prescaler)
/256 (From prescaler)
/1024 (From prescaler)
4
R/W
0
3
R/W
0
2
R/W
0
1
0
R/W
0
R/W
0
TCNT0
7593K–AVR–11/09
110.