AT90USB1287-AU Atmel, AT90USB1287-AU Datasheet - Page 291

• Manufacturer Part Number: AT90USB1287-AU
• Description: IC AVR MCU 128K 64TQFP
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB1287-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART, USB, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 48
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: AT90USBx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire/SPI/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525, ATAVRQTOUCHX
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Controller Family/series: AVR USB
• No. Of I/o's: 48
• Eeprom Memory Size: 4KB
• Ram Memory Size: 8KB
• Cpu Speed: 20MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: AT90USB1287-16AU; AT90USB1287-16AU

23.4
23.5
23.6
7593K–AVR–11/09
Device Detection
Pipe Selection
Pipe Configuration
USB host controller state after an hardware reset is ‘Reset’. When the USB controller is enabled
and the USB Host controller is selected, the USB controller is in ‘Idle’ state. In this state, the
USB Host controller waits for the Device connection, with a minimum power consumption.
The USB Pad should be in Idle mode. The macro does not need to have the PLL activated to
enter in ‘Host Ready’ state.
The Host controller enters in Suspend state when the USB bus is in Suspend state, i.e. when the
Host controller doesn’t generate the Start of Frame. In this state, the USB consumption is mini-
mum. The Host controller exits to the Suspend state when starting to generate the SOF over the
USB line.
A Device is detected by the USB controller when the USB bus if different from D+ and D- low. In
other words, when the USB Host Controller detects the Device pull-up on the D+ line. To enable
this detection, the Host Controller has to provide the Vbus power supply to the Device.
The Device Disconnection is detected by the USB Host controller when the USB Idle correspond
to D+ and D- low on the USB line.
Prior to any operation performed by the CPU, the Pipe must first be selected. This is done by
setting PNUM2:0 bits (UPNUM register) with the Pipe number which will be managed by the
CPU.
The CPU can then access to the various Pipe registers and data.
The following flow must be respected in order to activate a Pipe:
AT90USB64/128
291