AT90USB1287-AU Atmel, AT90USB1287-AU Datasheet - Page 70

• Manufacturer Part Number: AT90USB1287-AU
• Description: IC AVR MCU 128K 64TQFP
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB1287-AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART, USB, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 48
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: AT90USBx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire/SPI/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525, ATAVRQTOUCHX
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Controller Family/series: AVR USB
• No. Of I/o's: 48
• Eeprom Memory Size: 4KB
• Ram Memory Size: 8KB
• Cpu Speed: 20MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: AT90USB1287-16AU; AT90USB1287-16AU

9.1.1
9.1.2
70
AT90USB64/128
Moving Interrupts Between Application and Boot Space
MCU Control Register – MCUCR
Table 9-2.
Note:
The General Interrupt Control Register controls the placement of the Interrupt Vector table.
• Bit 1 – IVSEL: Interrupt Vector Select
When the IVSEL bit is cleared (zero), the Interrupt Vectors are placed at the start of the Flash
memory. When this bit is set (one), the Interrupt Vectors are moved to the beginning of the Boot
Loader section of the Flash. The actual address of the start of the Boot Flash Section is deter-
mined by the BOOTSZ Fuses. Refer to the section
details. To avoid unintentional changes of Interrupt Vector tables, a special write procedure must
be followed to change the IVSEL bit:
Interrupts will automatically be disabled while this sequence is executed. Interrupts are disabled
in the cycle IVCE is set, and they remain disabled until after the instruction following the write to
IVSEL. If IVSEL is not written, interrupts remain disabled for four cycles. The I-bit in the Status
Register is unaffected by the automatic disabling.
Note:
• Bit 0 – IVCE: Interrupt Vector Change Enable
Bit
Read/Write
Initial Value
BOOTRST
a. Write the Interrupt Vector Change Enable (IVCE) bit to one.
b. Within four cycles, write the desired value to IVSEL while writing a zero to IVCE.
1
1
0
0
1. The Boot Reset Address is shown in
If Interrupt Vectors are placed in the Boot Loader section and Boot Lock bit BLB02 is programmed,
interrupts are disabled while executing from the Application section. If Interrupt Vectors are placed
in the Application section and Boot Lock bit BLB12 is programed, interrupts are disabled while
executing from the Boot Loader section. Refer to the section
for details on Boot Lock bits.
means unprogrammed while “0” means programmed.
7
JTD
R/W
0
Reset and Interrupt Vectors Placement
IVSEL
0
1
0
1
6
–
R
0
Reset Address
0x0000
0x0000
Boot Reset Address
Boot Reset Address
5
–
R
0
4
PUD
R/W
0
Table 28-8 on page
3
–
R
0
Interrupt Vectors Start Address
0x0002
Boot Reset Address + 0x0002
0x0002
Boot Reset Address + 0x0002
(1)
“Memory Programming” on page 366
2
–
R
0
“Memory Programming” on page 366
364. For the BOOTRST Fuse “1”
1
IVSEL
R/W
0
0
IVCE
R/W
0
MCUCR
7593K–AVR–11/09
for