C8051F352-GQR Silicon Laboratories Inc, C8051F352-GQR Datasheet - Page 115

• Manufacturer Part Number: C8051F352-GQR
• Description: IC 8051 MCU 8K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F352-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x16b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Core: 8051
• Processor Series: C8051F3x
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 50 MHz
• Data Ram Size: 768 B
• Data Rom Size: 128 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 17
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.7 V to 3.6 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 16 bit
• A/d Channels Available: 8
• Height: 1.4 mm
• Interface Type: I2C, SMBus, SPI, UART
• Length: 7 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 7 mm
• For Use With: 336-1083 - DEV KIT FOR F350/351/352/353
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

14. Reset Sources
Reset circuitry allows the controller to be easily placed in a predefined default condition. On entry to this
reset state, the following occur:
•
•
•
•
All SFRs are reset to the predefined values noted in the SFR detailed descriptions. The contents of internal
data memory are unaffected during a reset; any previously stored data is preserved. However, since the
stack pointer SFR is reset, the stack is effectively lost, even though the data on the stack is not altered.
The Port I/O latches are reset to 0xFF (all logic ones) in open-drain mode. Weak pull-ups are enabled dur-
ing and after the reset. For V
exits the reset state.
On exit from the reset state, the program counter (PC) is reset, and the system clock defaults to the inter-
nal oscillator. Refer to Section “17. Oscillators’ on page 129 for information on selecting and configuring
the system clock source. The Watchdog Timer is enabled with the system clock divided by 12 as its clock
source (Section “23.3. Watchdog Timer Mode’ on page 220 details the use of the Watchdog Timer). Pro-
gram execution begins at location 0x0000.
CIP-51 halts program execution
Special Function Registers (SFRs) are initialized to their defined reset values
External Port pins are forced to a known state
Interrupts and timers are disabled.
Px.x
Px.x
System
Clock
Comparator 0
+
-
Detector
Missing
C0RSEF
Clock
(one-
shot)
Microcontroller
EN
DD
Extended Interrupt
Monitor and power-on resets, the /RST pin is driven low until the device
CIP-51
Handler
Core
Figure 14.1. Reset Sources
WDT
PCA
EN
VDD
System Reset
Supply
Monitor
+
-
Rev. 1.1
Enable
(Software Reset)
SWRSF
'0'
Power On
Reset
C8051F350/1/2/3
Operation
FLASH
Errant
(wired-OR)
Reset
Funnel
/RST
115