C8051F352-GQR Silicon Laboratories Inc, C8051F352-GQR Datasheet - Page 118

• Manufacturer Part Number: C8051F352-GQR
• Description: IC 8051 MCU 8K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F352-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x16b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Core: 8051
• Processor Series: C8051F3x
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 50 MHz
• Data Ram Size: 768 B
• Data Rom Size: 128 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 17
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.7 V to 3.6 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 16 bit
• A/d Channels Available: 8
• Height: 1.4 mm
• Interface Type: I2C, SMBus, SPI, UART
• Length: 7 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 7 mm
• For Use With: 336-1083 - DEV KIT FOR F350/351/352/353
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

C8051F350/1/2/3
14.3. External Reset
The external /RST pin provides a means for external circuitry to force the device into a reset state. Assert-
ing an active-low signal on the /RST pin generates a reset; an external pull-up and/or decoupling of the
/RST pin may be necessary to avoid erroneous noise-induced resets. See Table 14.1 for complete /RST
pin specifications. The PINRSF flag (RSTSRC.0) is set on exit from an external reset.
14.4. Missing Clock Detector Reset
The Missing Clock Detector (MCD) is a one-shot circuit that is triggered by the system clock. If the system
clock remains high or low for more than 100 µs, the one-shot will time out and generate a reset. After a
MCD reset, the MCDRSF flag (RSTSRC.2) will read ‘1’, signifying the MCD as the reset source; otherwise,
this bit reads ‘0’. Writing a ‘1’ to the MCDRSF bit enables the Missing Clock Detector; writing a ‘0’ disables
it. The state of the /RST pin is unaffected by this reset.
14.5. Comparator0 Reset
Comparator0 can be configured as a reset source by writing a ‘1’ to the C0RSEF flag (RSTSRC.5).
Comparator0 should be enabled and allowed to settle prior to writing to C0RSEF to prevent any turn-on
chatter on the output from generating an unwanted reset. The Comparator0 reset is active-low: if the non-
inverting input voltage (on CP0+) is less than the inverting input voltage (on CP0–), the device is put into
the reset state. After a Comparator0 reset, the C0RSEF flag (RSTSRC.5) will read ‘1’ signifying
Comparator0 as the reset source; otherwise, this bit reads ‘0’. The state of the /RST pin is unaffected by
this reset.
14.6. PCA Watchdog Timer Reset
The programmable Watchdog Timer (WDT) function of the Programmable Counter Array (PCA) can be
used to prevent software from running out of control during a system malfunction. The PCA WDT function
can be enabled or disabled by software as described in Section “23.3. Watchdog Timer Mode’ on
page 220; the WDT is enabled and clocked by SYSCLK / 12 following any reset. If a system malfunction
prevents user software from updating the WDT, a reset is generated and the WDTRSF bit (RSTSRC.5) is
set to ‘1’. The state of the /RST pin is unaffected by this reset.
14.7. Flash Error Reset
If a Flash read/write/erase or program read targets an illegal address, a system reset is generated. This
may occur due to any of the following:
•
•
•
•
The FERROR bit (RSTSRC.6) is set following a Flash error reset. The state of the /RST pin is unaffected
by this reset.
14.8. Software Reset
Software may force a reset by writing a ‘1’ to the SWRSF bit (RSTSRC.4). The SWRSF bit will read ‘1’ fol-
lowing a software forced reset. The state of the /RST pin is unaffected by this reset.
118
A Flash write or erase is attempted above user code space. This occurs when PSWE is set to ‘1’ and a
MOVX write operation targets an address above address 0x1DFF.
A Flash read is attempted above user code space. This occurs when a MOVC operation targets an
address above address 0x1DFF.
A Program read is attempted above user code space. This occurs when user code attempts to branch
to an address above 0x1DFF.
A Flash read, write or erase attempt is restricted due to a Flash security setting (see Section
“15.3. Security Options’ on page 123).
Rev. 1.1