C8051F018-GQR Silicon Laboratories Inc, C8051F018-GQR Datasheet - Page 71

• Manufacturer Part Number: C8051F018-GQR
• Description: IC 8051 MCU 16K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F018r

Specifications of C8051F018-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 1.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F005DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

The lock bits can always be read and cleared to logic 0 regardless of the security setting applied to the block
containing the security bytes. This allows additional blocks to be protected after the block containing the security
bytes has been locked. However, the only means of removing a lock once set is to erase the entire program memory
space by performing a JTAG erase operation (i.e. cannot be done in user firmware). NOTE: Addressing either
security byte while performing a JTAG erase operation will automatically initiate erasure of the entire
program memory space (except for the reserved area). This erasure can only be performed via JTAG. If a
non-security byte in the 0x3C00-0x3DFF page is addressed during erasure, only that page (including the
security bytes) will be erased.
The Flash Access Limit security feature (see Figure 9.3) protects proprietary program code and data from being read
by software running on the C8051F018/9 MCUs. This feature provides support for OEMs that wish to program the
MCU with proprietary value-added firmware before distribution. The value-added firmware can be protected while
allowing additional code to be programmed in remaining program memory space later.
The Software Read Limit (SRL) is a 16-bit address that establishes two logical partitions in the program memory
space. The first is an upper partition consisting of all the program memory locations at or above the SRL address,
and the second is a lower partition consisting of all the program memory locations starting at 0x0000 up to (but
excluding) the SRL address. Software in the upper partition can execute code in the lower partition, but is
71
FLASH Read Lock Byte
Bits7-0: Each bit locks a corresponding block of memory. (Bit 7 is MSB.)
FLASH Write/Erase Lock Byte
FLASH Access Limit Register (FLACL)
Bits7-0: Each bit locks a corresponding block of memory.
C8051F018
C8051F019
0: Read operations are locked (disabled) for corresponding block across the JTAG interface.
1: Read operations are unlocked (enabled) for corresponding block across the JTAG interface.
0: Write/Erase operations are locked (disabled) for corresponding block across the JTAG interface.
1: Write/Erase operations are unlocked (enabled) for corresponding block across the JTAG interface.
The content of this register is used as the high byte of the 16-bit software read limit address. The 16-
bit read limit address value is calculated as 0xNN00 where NN is replaced by the contents of this
register. Software running at or above this address is prohibited from using the MOVX or MOVC
instructions to read, write, or erase, locations below this address. Any attempts to read locations
below this limit will return the value 0x00.
Program Memory
Space
Figure 9.2. Flash Program Memory Security Bytes
Write/Erase Lock Byte
Software Read Limit
Read Lock Byte
Reserved
Rev. 1.2
0x807F
0x8000
0x7FFF
0x3E00
0x3DFF
0x3DF
E
0x3DFD
0x0000
Read and Write/Erase Security Bits.
(Bit 7 is MSB.)
Note: Bits 7-0 must all be set to lock
the block at 0x8000-0x807F
Bit
7
6
5
4
3
2
1
0
Memory Block
0x3000 - 0x3FFF
0x2000 - 0x2FFF
0x1000 - 0x1FFF
0x0000 - 0x0FFF