SFPA8192Q1BO2TO-I-QT-223-STD Swissbit NA Inc, SFPA8192Q1BO2TO-I-QT-223-STD Datasheet - Page 11

• Manufacturer Part Number: SFPA8192Q1BO2TO-I-QT-223-STD
• Description: FLASH SSD SMART UDMA 2.5" 8GB
• Manufacturer: Swissbit NA Inc
• Series: P-120r

Specifications of SFPA8192Q1BO2TO-I-QT-223-STD

• Memory Size: 8GB
• Memory Type: FLASH
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 1052-1025

5.3 Electrical Specification
Table 15
The current is measured by connecting an amp meter in series with the Vcc supply. The meter should be set
to the 2A scale range, and have a fast current probe with an RC filter with a time constant of 0.1ms. Current
measurements are taken while looping on a data transfer command with a sector count of 128. Current
consumption values for both read and write commands are not to exceed the Maximum Average RMS
Current specified in Table 14.
Table 13: Absolute Maximum Conditions
Parameter
Input Power
Voltage on any pin except VCC with respect to GND
Table 14: Input Power write and read tests
Mode
UDMA4
MDMA2
Table 15: Input Leakage current
Table 16: Input characteristics
Table 17: Output Drive Type
Table 18: Output Drive Characteristics
Swissbit AG
Industriestrasse 4
CH-9552 Bronschhofen
Switzerland
Type
Type
1.
Type
Type
1.
Opx
Onx
Ozx
IxU
IxD
Otx
IxZ
2
3
X
1
2
3
1
-
x refers to the characteristics described in Table 16 For example, OT3 refers to totem pole output with a type 3 output drive
Vcc = 5V ± 10%
0°C to +70°C
x refers to the characteristics described in Table 16 For example, I1U indicates a pull up resistor with a type 1 input
characteristic.
characteristic.
Table 18 define the DC Characteristics SSD. Unless otherwise stated, conditions are:
Parameter
Input Leakage Current
Pull Up Resistor
Pull Down Resistor
Leakage Current
Output Voltage
Output Voltage
Output Voltage
Parameter
Tri-State
Swissbit reserves the right to change products or specifications without notice.
Input Voltage CMOS Schmitt Trigger
Maximum Average RMS Current
(1)
Tri-State N-P Channel
Input Voltage CMOS
Input Voltage CMOS
N-Channel Only
P-Channel Only
Symbol
Output Type
(1)
Totempole
Parameter
V
V
V
V
V
V
I
OH
OH
OH
OZ
OL
OL
OL
140mA
110mA
Conditions
I
I
I
I
OH
I
I
Symbol
V
V
OH
OH
OL
OL
OL
OL
OH
RPU1
RPD1
[e-mail]
= -1mA
= -1mA
= -1mA
= 4mA
= 4mA
= 4mA
= Gnd
IL
= Vcc
www.swissbit.com
Conditions
V
V
Vcc = 5.0V
Vcc = 5.0V
IH
IL
=Vcc
= GND
Min.
-10
2.4
2.4
2.4
Symbol
VCC
V
Symbol
V
V
V
V
V
V
TH
IH
IH
TL
Min.
IL
IL
50
50
-1
Typ.
Min.
-0.3
-0.3
-0.3
2.0
2.0
2.0
Typ.
Valid Conditions
P-120_data_sheet_PA-QxBO_Rev100.doc
-0.5V to VCC+0.5V
Typ.
I
I
I
I
OH
OH
OH
OL
-0.3V to 6.5V
Max.
0.45
0.45
0.45
-40… +85 °C
Conditions
10
Conditions
& I
& I
only
only
Max.
500
500
1
OL
OL
Max.
0.8
0.8
0.8
5.3
5.3
5.3
kOhm
kOhm
Units
Units
Units
µA
µA
Page
Revision: 1.00
V
V
V
V
V
V
11 of 76