ST7LIT15BF0 STMicroelectronics, ST7LIT15BF0 Datasheet - Page 104

• Manufacturer Part Number: ST7LIT15BF0
• Description: 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI
• Manufacturer: STMicroelectronics

Specifications of ST7LIT15BF0

• Up To 4 Kbytes Single Voltage Extended Flash (xflash) Program Memory With Read-out Protection, In-circuit Programming And In-application Programming (icp And Iap). 10k Write/erase Cycles Guaranteed, Data Retention: 20 years at 55˚C.
• 128 Bytes Data Eeprom With Read-out Protection. 300k Write/erase Cycles Guaranteed, Data Retention: 20 years at 55˚C.
• Clock Sources: Internal 1% RC oscillator (on ST7FLITE15B and ST7FLITE19B), crystal/ceramic resonator or external clock
• Five Power Saving Modes: Halt, Active-Halt, Auto Wake-up from Halt, Wait and Slow

ST7LITE1xB
12 INSTRUCTION SET
12.1 ST7 ADDRESSING MODES
The ST7 Core features 17 different addressing
modes which can be classified in seven main
groups:
Table 22. ST7 Addressing Mode Overview
Note:
1. At the time the instruction is executed, the Program Counter (PC) points to the instruction following JRxx.
104/159
Inherent
Immediate
Direct
Indexed
Indirect
Relative
Bit operation
Inherent
Immediate
Short
Long
No Offset
Short
Long
Short
Long
Short
Long
Relative
Relative
Bit
Bit
Bit
Bit
Addressing Mode
Mode
Direct
Direct
Direct
Direct
Direct
Indirect
Indirect
Indirect
Indirect
Direct
Indirect
Direct
Indirect
Direct
Indirect
Indexed
Indexed
Indexed
Indexed
Indexed
Relative
Relative
ld A,#$55
ld A,($55,X)
ld A,([$55],X)
jrne loop
nop
ld A,$55
bset
byte,#5
Example
nop
ld A,#$55
ld A,$10
ld A,($10,X)
ld A,[$10]
jrne loop
jrne [$10]
bset $10,#7
bset [$10],#7
btjt $10,#7,skip
btjt [$10],#7,skip 00..FF
ld A,$1000
ld A,(X)
ld A,($1000,X)
ld A,[$10.w]
ld A,([$10],X)
ld A,([$10.w],X)
Syntax
00..FF
0000..FFFF
00..FF
00..1FE
0000..FFFF
00..FF
0000..FFFF
00..1FE
0000..FFFF
PC-128/PC+127
PC-128/PC+127
00..FF
00..FF
00..FF
Destination/
Source
The ST7 Instruction set is designed to minimize
the number of bytes required per instruction: To do
so, most of the addressing modes may be subdi-
vided in two submodes called long and short:
– Long addressing mode is more powerful be-
– Short addressing mode is less powerful because
The ST7 Assembler optimizes the use of long and
short addressing modes.
cause it can use the full 64 Kbyte address space,
however it uses more bytes and more CPU cy-
cles.
it can generally only access page zero (0000h -
00FFh range), but the instruction size is more
compact, and faster. All memory to memory in-
structions use short addressing modes only
(CLR, CPL, NEG, BSET, BRES, BTJT, BTJF,
INC, DEC, RLC, RRC, SLL, SRL, SRA, SWAP)
1)
1)
00..FF
00..FF
00..FF
00..FF
00..FF
00..FF
00..FF
Address
Pointer
(Hex.)
byte
word
byte
word
byte
byte
byte
Pointer
(Hex.)
Size
+ 0
+ 1
+ 1
+ 2
+ 0 (with X register)
+ 1 (with Y register)
+ 1
+ 2
+ 2
+ 2
+ 2
+ 2
+ 1
+ 2
+ 1
+ 2
+ 2
+ 3
(Bytes)
Length