ST7LIT15BF0 STMicroelectronics, ST7LIT15BF0 Datasheet - Page 38

• Manufacturer Part Number: ST7LIT15BF0
• Description: 8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, DATA EEPROM, ADC, 5 TIMERS, SPI
• Manufacturer: STMicroelectronics

Specifications of ST7LIT15BF0

• Up To 4 Kbytes Single Voltage Extended Flash (xflash) Program Memory With Read-out Protection, In-circuit Programming And In-application Programming (icp And Iap). 10k Write/erase Cycles Guaranteed, Data Retention: 20 years at 55˚C.
• 128 Bytes Data Eeprom With Read-out Protection. 300k Write/erase Cycles Guaranteed, Data Retention: 20 years at 55˚C.
• Clock Sources: Internal 1% RC oscillator (on ST7FLITE15B and ST7FLITE19B), crystal/ceramic resonator or external clock
• Five Power Saving Modes: Halt, Active-Halt, Auto Wake-up from Halt, Wait and Slow

ST7LITE1xB
INTERRUPTS (Cont’d)
EXTERNAL INTERRUPT CONTROL REGISTER
(EICR)
Read/Write
Reset Value: 0000 0000 (00h)
Bits 7:6 = IS3[1:0] ei3 sensitivity
These bits define the interrupt sensitivity for ei3
(Port B0) according to
Bits 5:4 = IS2[1:0] ei2 sensitivity
These bits define the interrupt sensitivity for ei2
(Port B3) according to
Bits 3:2 = IS1[1:0] ei1 sensitivity
These bits define the interrupt sensitivity for ei1
(Port A7) according to
Bits 1:0 = IS0[1:0] ei0 sensitivity
These bits define the interrupt sensitivity for ei0
(Port A0) according to
Notes:
1. These 8 bits can be written only when the I bit in
the CC register is set.
2. Changing the sensitivity of a particular external
interrupt clears this pending interrupt. This can be
used to clear unwanted pending interrupts. Refer
to section “External Interrupt Function” on
page 48.
Table 6. Interrupt Sensitivity Bits
38/159
1
ISx1 ISx0
IS31
0
0
1
1
7
IS30
0
1
0
1
IS21
External Interrupt Sensitivity
IS20
Falling edge & low level
Rising and falling edge
Table
Table
Table
Table
Falling edge only
Rising edge only
IS11
6.
6.
6.
6.
IS10
IS01
IS00
0
EXTERNAL INTERRUPT SELECTION REGIS-
TER (EISR)
Read/Write
Reset Value: 0000 1100 (0Ch)
Bits 7:6 = ei3[1:0] ei3 pin selection
These bits are written by software. They select the
Port B I/O pin used for the ei3 external interrupt ac-
cording to the table below.
External Interrupt I/O pin selection
Note:
1. Reset State
Bits 5:4 = ei2[1:0] ei2 pin selection
These bits are written by software. They select the
Port B I/O pin used for the ei2 external interrupt ac-
cording to the table below.
External Interrupt I/O pin selection
Notes:
1. Reset State
2. PB4 cannot be used as an external interrupt in
HALT mode.
ei31
7
ei31
ei21
0
0
1
0
0
1
1
ei30
ei30
ei20
ei21
0
1
0
0
1
0
1
ei20
ei11
I/O Pin
I/O Pin
PB0
PB3
PB4
ei10
PB1
PB2
PB5
PB6
1)
1)
2)
ei01
ei00
0