CYP15G0101DXB Cypress Semiconductor Corporation., CYP15G0101DXB Datasheet - Page 5

• Manufacturer Part Number: CYP15G0101DXB
• Description: Single-channel Hotlink Ii Transceiver
• Manufacturer: Cypress Semiconductor Corporation.

Document #: 38-02031 Rev. *J
Pin Descriptions
Pin Name
Transmit Path Data Signals
TXPER
TXCT[1:0]
TXD[7:0]
TXOP
SCSEL
Note:
3.
When REFCLK is configured for half-rate operation (TXRATE
of REFCLK.
I/O Characteristics Signal Description
LVTTL Output,
changes relative to
REFCLK↑
LVTTL Input,
synchronous,
sampled by TXCLK↑
or REFCLK↑
LVTTL Input,
synchronous,
sampled by TXCLK↑
or REFCLK↑
LVTTL Input,
synchronous,
internal pull-up,
sampled by TXCLK↑
or REFCLK↑
LVTTL Input,
synchronous,
internal pull-down,
sampled by TXCLK↑
or REFCLK↑
CYP(V)(W)15G0101DXB Single-channel HOTLink II
[3]
[3]
[3]
[3]
[3]
Transmit Path Parity Error. Active HIGH. Asserted (HIGH) if parity checking is enabled
(PARCTL ≠ LOW) and a parity error is detected at the Encoder. This output is HIGH for one
transmit character-clock period to indicate detection of a parity error in the character
presented to the Encoder.
If a parity error is detected, the character in error is replaced with a C0.7 character to force
a corresponding bad-character detection at the remote end of the link. This replacement
takes place regardless of the encoded/un-encoded state of the interface.
When BIST is enabled for the specific transmit channel, BIST progress is presented on this
output. Once every 511 character times (plus a 16-character Word Sync Sequence when
the receive channel is clocked by REFCLK, i.e., RXCKSEL = LOW), the TXPER signal
pulses HIGH for one transmit-character clock period (if RXCKSEL = MID) or seventeen
transmit-character clock periods (if RXCKSEL = LOW or HIGH) to indicate a complete pass
through the BIST sequence. For RXCKSEL = LOW or HIGH, If TXMODE[1:0] = LL, then no
Word Sync Sequence is sent in BIST, and TXPER pulses HIGH for one transmit-character
clock period.
This output also provides an indication of a Phase-Align Buffer underflow/overflow
condition. When the Phase-Align Buffer is enabled (TXCKSEL ≠ LOW, or TXCKSEL = LOW
and TXRATE = HIGH), and an underflow/overflow condition is detected, TXPER is asserted
and remains asserted until either an atomic Word Sync Sequence is transmitted or TXRST is
sampled LOW to recenter the Phase-Align Buffer.
Transmit Control. These inputs are captured on the rising edge of the transmit interface
clock as selected by TXCKSEL, and are passed to the Encoder or Transmit Shifter. They
identify how the TXD[7:0] characters are interpreted. When the Encoder is enabled, these
inputs determine if the TXD[7:0] character is encoded as Data, a Special Character code,
a K28.5 fill character or a Word Sync Sequence. When the Encoder is bypassed, these
inputs are interpreted as data bits. See Table 1 for details.
Transmit Data Inputs. These inputs are captured on the rising edge of the transmit
interface clock as selected by TXCKSEL, and passed to the Encoder or Transmit Shifter.
When the Encoder is enabled (TXMODE[1] ≠ LOW), TXD[7:0] specify the specific data or
command character to be sent. When the Encoder is bypassed, these inputs are interpreted
as data bits of the 10-bit input character. See Table 1 for details.
Transmit Path Odd Parity. When parity checking is enabled (PARCTL ≠ LOW), the parity
captured at this input is XORed with the data on the TXD bus (and sometimes TXCT[1:0])
to verify the integrity of the captured character. See Table 2 for details.
Special Character Select. Used in some transmit modes along with TXCTx[1:0] to encode
special characters or to initiate a Word Sync Sequence. When the transmit path is
configured to select TXCLK to clock the input register (TXCKSEL = MID or HIGH), SCSEL
is captured relative to TXCLK↑.
=
HIGH), this input is sampled (or the outputs change) relative to both the rising and falling edges
CYW15G0101DXB
CYV15G0101DXB
CYP15G0101DXB
Page 5 of 39
[+] Feedback