CYP15G0101DXB Cypress Semiconductor Corporation., CYP15G0101DXB Datasheet - Page 9

• Manufacturer Part Number: CYP15G0101DXB
• Description: Single-channel Hotlink Ii Transceiver
• Manufacturer: Cypress Semiconductor Corporation.

Document #: 38-02031 Rev. *J
Pin Descriptions
Pin Name
REFCLK±
TRSTZ
Analog I/O and Control
OUT1±
OUT2±
IN1±
IN2±
INSEL
SDASEL
LPEN
OELE
I/O Characteristics Signal Description
Differential LVPECL
or single-ended
LVTTL input clock
LVTTL Input,
internal pull-up
CML Differential
Output
CML Differential
Output
LVPECL Differential
Input, with internal
DC restoration
LVPECL Differential
Input, with internal
DC restoration
LVTTL Input,
asynchronous
3-Level Select,
static control input
LVTTL Input,
asynchronous,
internal pull-down
LVTTL Input,
asynchronous,
internal pull-up
CYP(V)(W)15G0101DXB Single-channel HOTLink II (continued)
[4]
Reference Clock. This clock input is used as the timing reference for the transmit PLL. It
is also used as the centering frequency of the Range Controller block of the Receive CDR
PLLs. This input clock may also be selected to clock the transmit and receive parallel inter-
faces.
When driven by a single-ended LVCMOS or LVTTL clock source, the clock source may be
connected to either the true or complement REFCLK input, with the alternate REFCLK input
left open (floating). When driven by an LVPECL clock source, the clock must be a differential
clock, using both inputs. When TXCKSEL = LOW, REFCLK is also used as the clock for the
parallel transmit data (input) interface. When RXCKSEL = LOW and Decoder is enabled,
the Elasticity buffer is enabled and REFCLK is used as the clock source for the parallel
receive data (output) interface.
If the Elasticity Buffer is used, framing characters will be inserted or deleted to/from the data
stream to compensate for frequency differences between the reference clock and recovered
clock. When addition happens, a K28.5 will be appended immediately after a framing
character is detected in the Elasticity Buffer. When deletion happens, a framing character
will be removed from the data stream when detected in the Elasticity Buffer.
Device Reset. Active LOW. Initializes all state machines and counters in the device.
When sampled LOW by the rising edge of REFLCK, this input resets the internal state
machines and sets the Elasticity Buffer pointers to a nominal offset. When the reset is
removed (TRSTZ sampled HIGH by REFCLK↑), the status and data outputs will become
deterministic in less than 16 REFCLK cycles. The BISTLE, OELE, and RXLE latches are
reset by TRSTZ. If the Elasticity Buffer or the Phase-Align Buffer are used, TRSTZ should
be applied after power up to initialize the internal pointers into these memory arrays.
Primary Differential Serial Data Outputs. These PECL-compatible CML outputs (+3.3V
referenced) are capable of driving terminated transmission lines or standard fiber-optic
transmitter modules.
Secondary Differential Serial Data Outputs. These PECL-compatible CML outputs
(+3.3V referenced) are capable of driving terminated transmission lines or standard
fiber-optic transmitter modules.
Primary Differential Serial Data Inputs. These inputs accept the serial data stream for
deserialization and decoding. The IN1± serial stream is passed to the receiver Clock and
Data Recovery (CDR) circuit to extract the data content when INSEL = HIGH.
Secondary Differential Serial Data Inputs. These inputs accept the serial data stream for
deserialization and decoding. The IN2± serial stream is passed to the receiver CDR circuit
to extract the data content when INSEL = LOW.
Receive Input Selector. Determines which external serial bit stream is passed to the receiver
CDR. When HIGH, the IN1± input is selected. When LOW, the IN2± input is selected.
Signal Detect Amplitude Level Select. Allows selection of one of three predefined
amplitude trip points for a valid signal indication, as listed in Table 10.
Loop-Back-Enable. Active HIGH. When asserted (HIGH), the transmit serial data is
internally routed to the receiver CDR circuit.All enabled serial drivers are forced to differ-
ential logic “1.” All serial data inputs are ignored.
Serial Driver Output Enable Latch Enable. Active HIGH. When OELE = HIGH, the signals
on the BOE[1:0] inputs directly control the OUTx± differential drivers. When the BOE[x] input
is HIGH, the associated OUTx± differential driver is enabled. When the BOE[x] input is LOW,
the associated OUTx± differential driver is powered down. When OELE returns LOW, the
last values present on BOE[1:0] are captured in the internal Output Enable Latch. The
specific mapping of BOE[1:0] signals to transmit output enables is listed in Table 8. If the
device is reset (TRSTZ is sampled LOW), the latch is reset to disable both outputs.
CYW15G0101DXB
CYV15G0101DXB
CYP15G0101DXB
Page 9 of 39
[+] Feedback