S25FL004K Meet Spansion Inc., S25FL004K Datasheet - Page 67

• Manufacturer Part Number: S25FL004K
• Description: 4-mbit / 8-mbit / 16-mbit Cmos 3.0 Volt Flash Memory With 104-mhz Spi Serial Peripheral Interface Multi I/o Bus
• Manufacturer: Meet Spansion Inc.

9.
9.1
July 14, 2011 S25FL004K-016K_00_02
(0.25D x 0.75E)
INDEX AREA
3
PACKAGE
SYMBOL
E1
JEDEC
A
9
A1
A2
E1
b1
c1
L1
L2
θ1
θ2
4
A
D
E
N
Physical Dimensions
b
c
e
L
h
θ
E1/2
A2
SOA008 narrow — 8-pin Plastic Small Outline Package (150-mils Body Width)
A1
0.0531
0.0039
0.0067
0.0067
0.0161
SOA 008 (inches)
0.052
0.012
0.011
0.10
MIN
MS-012(D)AA
0˚
5˚
0.236 BSC
0.193 BSC
0.1535 BSC
.050 BSC
.041 REF
.010 BSC
8
0˚
e
0.0688
0.0098
0.0098
0.061
0.020
0.019
0.009
0.035
0.196
MAX
15˚
8˚
A
B
3
D
1.35
0.10
1.32
0.31
0.27
0.17
0.17
0.41
0.25
4
MIN
0˚
5˚
SOA 008 (mm)
1.04 REF
0.25 BSC
MS-012(D)AA
1.27 BSC
4.90 BSC
6.00 BSC
5
5
3.90 BSC
8
0˚
MAX
1.75
0.25
1.55
0.51
0.48
0.25
0.23
0.89
0.50
15˚
8˚
D a t a
b
0.10
0.25
S25FL004K / S25FL008K / S25FL016K
C
M
E/2
0.20 C
C
S h e e t
A - B
C
D
E
0.10
A - B
D
SEATING PLANE
C
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
NOTES:
0.33
SEE
DETAIL B
.
ALL DIMENSIONS ARE IN BOTH INCHES AND MILLMETERS.
DIMENSIONING AND TOLERANCING PER ASME Y14.5M - 1994.
DIMENSION D DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 mm
PER END. DIMENSION E1 DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION INTERLEAD FLASH OR PROTRUSION
SHALL NOT EXCEED 0.25 mm PER SIDE. D AND E1
DIMENSIONS ARE DETERMINED AT DATUM H.
THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE
BOTTOM. DIMENSIONS D AND E1 ARE DETERMINED AT THE
OUTMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF
MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD
FLASH. BUT INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
DATUMS A AND B TO BE DETERMINED AT DATUM H.
"N" IS THE MAXIMUM NUMBER OF TERMINAL POSITIONS FOR
THE SPECIFIED PACKAGE LENGTH.
THE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD
BETWEEN 0.10 TO 0.25 mm FROM THE LEAD TIP.
DIMENSION "b" DOES NOT INCLUDE DAMBAR PROTRUSION.
ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.10 mm TOTAL
IN EXCESS OF THE "b" DIMENSION AT MAXIMUM MATERIAL
CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE
LOWER RADIUS OF THE LEAD FOOT.
THIS CHAMFER FEATURE IS OPTIONAL. IF IT IS NOT PRESENT,
THEN A PIN 1 IDENTIFIER MUST BE LOCATED WITHIN THE INDEX
AREA INDICATED.
LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED
FROM THE SEATING PLANE.
9
C
h
h
C
H
H
0
1
DETAIL B
PLATING
METAL
L1
BASE
WITH
L
A
0
A
c
2
SECTION A-A
0.07 R MIN.
0
(b)
b1
3528 \ 16-038.03 \ 11.02.05
7
L2
SEATING PLANE
GAUGE PLANE
c1
67