S25FL004K Meet Spansion Inc., S25FL004K Datasheet - Page 68

• Manufacturer Part Number: S25FL004K
• Description: 4-mbit / 8-mbit / 16-mbit Cmos 3.0 Volt Flash Memory With 104-mhz Spi Serial Peripheral Interface Multi I/o Bus
• Manufacturer: Meet Spansion Inc.

9.2
68
PACKAGE
SYMBOL
JEDEC
A1
A2
b1
E1
L1
L2
c1
θ1
θ2
D
A
b
E
e
L
N
c
θ
SOC008 wide — 8-pin Plastic Small Outline Package (208-mils Body Width)
0.0075
SOC 008 (inches)
0.069
0.002
0.067
0.014
0.013
0.006
0.020
MIN
0˚
5˚
0.315 BSC
0.208 BSC
0.208 BSC
.050 BSC
.049 REF
.010 BSC
0˚
8
0.0098
0.0095
0.085
0.075
0.019
0.018
0.008
0.030
MAX
15˚
8˚
1.753
0.051
0.356
0.330
0.191
0.152
0.508
1.70
MIN
0˚
5˚
SOC 008 (mm)
1.25 REF
0.25 BSC
1.27 BSC
8.001 BSC
5.283 BSC
5.283 BSC
8
0˚
2.159
0.249
0.483
0.457
0.241
0.203
0.762
MAX
1.91
15˚
8˚
S25FL004K / S25FL008K / S25FL016K
D a t a
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
NOTES:
ALL DIMENSIONS ARE IN BOTH INCHES AND MILLMETERS.
DIMENSIONING AND TOLERANCING PER ASME Y14.5M - 1994.
DIMENSION D DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 mm
PER END. DIMENSION E1 DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION INTERLEAD FLASH OR PROTRUSION
SHALL NOT EXCEED 0.25 mm PER SIDE. D AND E1
DIMENSIONS ARE DETERMINED AT DATUM H.
THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE
BOTTOM. DIMENSIONS D AND E1 ARE DETERMINED AT THE
OUTMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF
MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD
FLASH. BUT INCLUDING ANY MISMATCH BETWEEN THE TOP
AND BOTTOM OF THE PLASTIC BODY.
DATUMS A AND B TO BE DETERMINED AT DATUM H.
"N" IS THE MAXIMUM NUMBER OF TERMINAL POSITIONS FOR
THE SPECIFIED PACKAGE LENGTH.
THE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD
BETWEEN 0.10 TO 0.25 mm FROM THE LEAD TIP.
DIMENSION "b" DOES NOT INCLUDE DAMBAR PROTRUSION.
ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.10 mm TOTAL
IN EXCESS OF THE "b" DIMENSION AT MAXIMUM MATERIAL
CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE
LOWER RADIUS OF THE LEAD FOOT.
THIS CHAMFER FEATURE IS OPTIONAL. IF IT IS NOT PRESENT,
THEN A PIN 1 IDENTIFIER MUST BE LOCATED WITHIN THE INDEX
AREA INDICATED.
LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED
FROM THE SEATING PLANE.
S h e e t
S25FL004K-016K_00_02 July 14, 2011
3602 \ 16-038.03 \ 9.1.6