PF38F5070M0P0B NUMONYX [Numonyx B.V], PF38F5070M0P0B Datasheet - Page 20

• Manufacturer Part Number: PF38F5070M0P0B
• Description: Numonyx Wireless Flash Memory (W18)
• Manufacturer: NUMONYX [Numonyx B.V]

Table 8:
Datasheet
20
F[2:1]-VCC
P-Mode,
F-RST#
F-VPEN
F-WP#
R-UB#
R-LB#
F-VPP,
S-VCC
P-VCC
ADV#
P-CRE
VCCQ
WAIT
VSS
RFU
DU
Signal Descriptions - QUAD+ Package (Sheet 2 of 2)
Output
Power
Power
Power
Power
Power
Power
Input
Input
Input
Input
Input
—
—
WAIT: Output signal.
Indicates invalid data during synchronous array or non-array flash reads. Read Configuration Register
bit 10 (RCR[10]) determines WAIT-asserted polarity (high or low). WAIT is High-Z if F-CE# is
deasserted; WAIT is not gated by F-OE#.
FLASH WRITE PROTECT: Low-true input.
F-WP# enables/disables the lock-down protection mechanism of the selected flash die.
ADDRESS VALID: Low-true input.
During synchronous flash read operations, addresses are latched on the rising edge of ADV#, or on
the next valid CLK edge with ADV# low, whichever occurs first.
In asynchronous flash read operations, addresses are latched on the rising edge of ADV#, or are
continuously flow-through when ADV# is kept asserted.
RAM UPPER / LOWER BYTE ENABLES: Low-true input.
During RAM read and write cycles, R-UB# low enables the RAM high order bytes on D[15:8], and R-
LB# low enables the RAM low-order bytes on D[7:0].
R-UB# and R-LB# are available on stacked combinations with PSRAM or SRAM die and are RFU on
flash-only stacked combinations.
FLASH RESET: Low-true input.
F-RST# low initializes flash internal circuitry and disables flash operations. F-RST# high enables flash
operation. Exit from reset places the flash in asynchronous read array mode.
P-Mode (PSRAM Mode): Low-true input.
P-Mode is used to program the Configuration Register, and enter/exit Low Power Mode of PSRAM die.
P-Mode is available on stacked combinations with asynchronous-only PSRAM die.
P-CRE (PSRAM Configuration Register Enable): High-true input.
P-CRE is high, write operations load the refresh control register or bus control register.
P-CRE is applicable only on combinations with synchronous PSRAM die.
P-Mode, P-CRE is an RFU on stacked combinations without PSRAM die.
FLASH PROGRAM AND ERASE POWER: Valid F-V
operations.
Flash memory array contents cannot be altered when F-V
operations at invalid F-V
datasheet for additional details.
F-VPEN (Erase/Program/Block Lock Enables) is not available for L18/L30 SCSP products.
FLASH LOGIC POWER: F1-VCC supplies power to the core logic of flash die #1; F2-VCC supplies
power to the core logic of flash die #2 and flash die #3. Write operations are inhibited when F-V
V
F2-VCC is available on stacked combinations with two or three flash dies, and is an RFU on stacked
combinations with only one flash die.
SRAM POWER SUPPLY: Supplies power for SRAM operations.
S-VCC is available on stacked combinations with SRAM die, and is RFU on stacked combinations
without SRAM die.
PSRAM POWER SUPPLY: Supplies power for PSRAM operations.
P-VCC is available on stacked combinations with PSRAM die, and is RFU on stacked combinations
without PSRAM die.
DEVICE I/O POWER: Supply power for the device input and output buffers.
DEVICE GROUND: Connect to system ground. Do not float any VSS connection.
RESERVED for FUTURE USE: Reserved for future device functionality/ enhancements. Contact
Numonyx regarding the use of balls designated RFU.
DO NOT USE: Do not connect to any other signal, or power supply; must be left floating.
• In synchronous array or non-array flash read modes, WAIT indicates invalid data when asserted
• In asynchronous flash page read, and all flash write modes, WAIT is asserted.
• F-WP# low enables the lock-down mechanism where locked down blocks cannot be unlocked with
• F-WP# high disables the lock-down mechanism, allowing locked down blocks to be unlocked with
LKO
and valid data when deasserted.
software commands.
software commands.
. Device operations at invalid F-V
PP
(F-V
PEN
) voltages should not be attempted. Refer to flash discrete product
CC
voltages should not be attempted.
PP
voltage on this ball enables flash program/erase
Numonyx™ Wireless Flash Memory (W18)
Numonyx™ Wireless Flash Memory (W18)
PP
(F-V
PEN
) < V
PPLK
(V
Order Number: 290701-18
PENLK
). Erase / program
November 2007
CC
<