PF38F5070M0P0B NUMONYX [Numonyx B.V], PF38F5070M0P0B Datasheet - Page 56
PF38F5070M0P0B
Manufacturer Part Number
PF38F5070M0P0B
Description
Numonyx Wireless Flash Memory (W18)
Manufacturer
NUMONYX [Numonyx B.V]
Datasheet
1.PF38F5070M0P0B.pdf
(102 pages)
- Current page: 56 of 102
- Download datasheet (2Mb)
10.3
10.4
Table 24: Device Identification Codes (Sheet 1 of 2)
Datasheet
56
Manufacturer ID
Device ID
Block Lock Status
Block Lock-Down Status
Configuration Register
Item
output on valid CLK edges following a minimum delay. However, for a synchronous non-
array read, the same word of data will be output on successive clock edges until the
burst length requirements are satisfied. See During synchronous read operations, WAIT
indicates invalid data when asserted, and valid data when deasserted with respect to a
valid clock edge. See
Read Array
The Read Array command places (or resets) the partition in read-array mode and is
used to read data from the flash memory array. Upon initial device power-up, or after
reset (RST# transitions from V
array mode. To read array data from the flash device, first write the Read Array
command (FFh) to the CUI and specify the desired word address. Then read from that
address. If a partition is already in read-array mode, issuing the Read Array command
is not required to read from that partition.
If the Read Array command is written to a partition that is erasing or programming, the
device presents invalid data on the bus until the program or erase operation completes.
After the program or erase finishes in that partition, valid array data can then be read.
If an Erase Suspend or Program Suspend command suspends the WSM, a subsequent
Read Array command places the addressed partition in read-array mode. The Read
Array command functions independently of V
Read Identifier
The Read Identifier mode outputs the manufacturer/device identifier, block lock status,
protection register codes, and Configuration Register data. The identifier information is
contained within a separate memory space on the device and can be accessed along
the 4-Mbit partition address range supplied by the Read Identifier command (90h)
address. Reads from addresses in
Identifier command to a partition that is programming or erasing places that partition’s
outputs in read ID mode while the partition continues to program or erase in the
background.
(2)
(2)
Partition
Partition
Partition
Base
Block
Block
Section 7.0, “AC Characteristics” on page 26
Address
IL
1
Offset
to V
00h
01h
02h
02h
05h
Table 24
IH
), all partitions default to asynchronous read-
Register Data
retrieve ID information. Issuing a Read
PP
D0 = 0
D0 = 1
D1 = 0
D1 = 1
0089h
8862h
8863h
8864h
8865h
8866h
8867h
Data
.
Numonyx™ Wireless Flash Memory (W18)
Numonyx™ Wireless Flash Memory (W18)
Numonyx
32-Mbit, Top Parameter Device
32-Mbit, Bottom Parameter Device
64-Mbit, Top Parameter Device
64-Mbit, Bottom Parameter Device
128-Mbit, Top Parameter Device
128-Mbit, Bottom Parameter Device
Block is unlocked
Block is locked
Block is not locked-down
Block is locked down
for additional details.
Order Number: 290701-18
Description
November 2007
Related parts for PF38F5070M0P0B
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Numonyx StrataFlash Wireless Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
8 Mbit, low voltage, Page-Erasable Serial Flash memory with byte alterability and a 50 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
128 Mbit (8 Mb ×16, multiple bank, multilevel interface, burst) 1.8 V supply, secure Flash memories
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
64-Mbit, dual I/O, 4-Kbyte subsector erase, serial flash memory with 75 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
512 Kbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
1 Mbit, serial Flash memory, 50 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
16 Mbit, serial Flash memory, 75 MHz SPI bus interface
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
Wireless Flash Memory (W18/W30 SCSP)
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
StrataFlash® Cellular Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
128 Mbit (8 Mb x 16, multiple bank, page, dual boot) 3 V supply Flash memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
32 Mbit (4Mb x8 or 2Mb x16, Dual Bank 8:24, Boot Block) 3V Supply Flash Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
32 Mbit (4Mb x8 or 2Mb x16, Dual Bank 16:16, Boot Block) 3V Supply Flash Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
64 Mbit (8Mb x8 or 4Mb x16, Multiple Bank, Page, Boot Block) 3V Supply Flash Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet:
Part Number:
Description:
64 Mbit (4Mb x16, Multiple Bank, Page, Boot Block) 3V Supply Flash Memory
Manufacturer:
NUMONYX [Numonyx B.V]
Datasheet: