MC9S12C32CFAE25 Freescale Semiconductor, MC9S12C32CFAE25 Datasheet - Page 469

• Manufacturer Part Number: MC9S12C32CFAE25
• Description: IC MCU 32K FLASH 25MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12C32CFAE25

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 31
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: S12C
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: CAN/SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 31
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68EVB912C32EE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• For Use With: CML12C32SLK - KIT STUDENT LEARNING 16BIT HCS12
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

16.5
This subsection describes how VREG3V3V2 controls the reset of the MCU.The reset values of registers
and signals are provided in
are listed in
16.5.1
During chip power-up the digital core may not work if its supply voltage V
deassertion level (V
kept high until V
continues the start-up sequence. The power-on reset is active in all operation modes of VREG3V3V2.
16.5.2
For details on low-voltage reset see
16.6
This subsection describes all interrupts originated by VREG3V3V2.
The interrupt vectors requested by VREG3V3V2 are listed in
priorities are defined at MCU level.
16.6.1
In FPM VREG3V3V2 monitors the input voltage V
status bit LVDS is set to 1. Vice versa, LVDS is reset to 0 when V
interrupt, indicated by flag LVIF = 1, is triggered by any change of the status bit LVDS if interrupt enable
bit LVIE = 1.
Freescale Semiconductor
Resets
Interrupts
Power-On Reset
Low-Voltage Reset
LVI — Low-Voltage Interrupt
Table
Low Voltage Interrupt (LVI)
On entering the Reduced Power Mode, the LVIF is not cleared by the
VREG3V3V2.
Power-on reset
Low-voltage reset
DD
16-4.
PORD
Interrupt Source
exceeds V
Reset Source
). Therefore, signal POR which forces the other blocks of the device into reset is
Section 16.3, “Memory Map and Register
PORD
Table 16-5. VREG3V3V2 — Interrupt Vectors
Table 16-4. VREG3V3V2 — Reset Sources
Section 16.4.6, “LVR — Low-Voltage
. Then POR becomes low and the reset generator of the device
MC9S12C-Family / MC9S12GC-Family
Always active
Available only in Full Performance Mode
LVIE = 1; Available only in Full Performance Mode
Chapter 16 Dual Output Voltage Regulator (VREG3V3V2) Block Description
Rev 01.24
NOTE
DDA
. Whenever V
Local Enable
Local Enable
Table
DDA
16-5. Vector addresses and interrupt
Definition”. Possible reset sources
DDA
rises above level V
drops below level V
DD
Reset”.
is below the POR
LVID
. An
LVIA
the
469