ST72F325K4T6 STMicroelectronics, ST72F325K4T6 Datasheet - Page 41

• Manufacturer Part Number: ST72F325K4T6
• Description: MCU 8BIT 16KB FLASH/ROM 32-LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F325K4T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 48
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7232X-EVAL, ST7232X-SK/RAIS, ST72325-D/RAIS, ST7MDT20-DVP3, ST7MDT20J-EMU3, ST7MDT20M-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• For Use With: 497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-5605

INTERRUPTS (Cont’d)
Table 9. Interrupt Mapping
Notes:
1. Exit from HALT possible when SPI is in slave mode.
2. Exit from HALT possible when PWM ART is in external clock mode.
7.6 EXTERNAL INTERRUPTS
7.6.1 I/O Port Interrupt Sensitivity
The external interrupt sensitivity is controlled by
the IPA, IPB and ISxx bits of the EICR register
(Figure
independent external interrupt source sensitivities.
Each external interrupt source can be generated
on four (or five) different events on the pin:
■
■
■
N°
10
11
12
13
Falling edge
Rising edge
Falling and rising edge
0
1
2
3
4
5
6
7
8
9
25). This control allows to have up to 4 fully
MCC/RTC/
PWM ART
TIMER A
TIMER B
Source
RESET
Block
TRAP
CSS
AVD
SPI
SCI
I2C
TLI
ei0
ei1
ei2
ei3
Reset
Software interrupt
External top level interrupt
Main clock controller time base interrupt
Safe oscillator activation interrupt
External interrupt port A3..0
External interrupt port F2..0
External interrupt port B3..0
External interrupt port B7..4
SPI peripheral interrupts
TIMER A peripheral interrupts
TIMER B peripheral interrupts
SCI Peripheral interrupts
Auxiliary Voltage detector interrupt
I2C Peripheral interrupts
PWM ART interrupt
Not used
Description
■
■
To guarantee correct functionality, the sensitivity
bits in the EICR register can be modified only
when the I1 and I0 bits of the CC register are both
set to 1 (level 3). This means that interrupts must
be disabled before changing sensitivity.
The pending interrupts are cleared by writing a dif-
ferent value in the ISx[1:0], IPA or IPB bits of the
EICR.
Falling edge and low level
Rising edge and high level (only for ei0 and ei2)
(see periph)
Register
MCCSR-
ARTCSR
SPICSR
SICSR
SICSR
SCISR
Label
TASR
TBSR
EICR
N/A
N/A
Priority
Priority
Priority
Higher
Order
Lower
ACTIVE
HALT/
HALT
from
yes
yes
Exit
yes
yes
yes
yes
yes
yes
yes
no
no
no
no
no
no
1
2
FFECh-FFEDh
FFFCh-FFFDh
FFEEh-FFEFh
FFEAh-FFEBh
FFFEh-FFFFh
FFFAh-FFFBh
FFE8h-FFE9h
FFE6h-FFE7h
FFE4h-FFE5h
FFE2h-FFE3h
FFE0h-FFE1h
FFF8h-FFF9h
FFF6h-FFF7h
FFF4h-FFF5h
FFF2h-FFF3h
FFF0h-FFF1h
ST72325xx
Address
Vector
41/197