ATTINY861-15MZ Atmel, ATTINY861-15MZ Datasheet - Page 176

• Manufacturer Part Number: ATTINY861-15MZ
• Description: MCU AVR 8K FLASH 15MHZ 32-QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY861-15MZ

• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Speed: 16MHz
• Number Of I /o: 16
• Eeprom Size: 512 x 8
• Core Processor: AVR
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Program Memory Size: 8KB (8K x 8)
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Connectivity: USI
• Core Size: 8-Bit
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRMC320
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

22.7.5
176
ATtiny261/461/861
Programming the EEPROM
Figure 22-3. Programming the Flash Waveforms
Note:
The EEPROM is organized in pages, see
EEPROM, the program data is latched into a page buffer. This allows one page of data to be
programmed simultaneously. The programming algorithm for the EEPROM data memory is as
follows (refer to
Data loading):
1. A: Load Command “0001 0001”.
2. G: Load Address High Byte (0x00 - 0xFF).
3. B: Load Address Low Byte (0x00 - 0xFF).
4. C: Load Data (0x00 - 0xFF).
5. E: Latch data (give PAGEL a positive pulse).
K: Repeat 3 through 5 until the entire buffer is filled.
L: Program EEPROM page
1. Set BS to “0”.
2. Give WR a negative pulse. This starts programming of the EEPROM page. RDY/BSY
3. Wait until to RDY/BSY goes high before programming the next page (See
goes low.
signal waveforms).
RESET +12V
PAGEL/BS1
RDY/BSY
XA1/BS2
XTAL1
DATA
1. “XX” is don’t care. The letters refer to the programming description above.
XA0
WR
OE
0x10
A
”Programming the Flash” on page 174
ADDR. LOW
B
DATA LOW
C
DATA HIGH
D
XX
E
ADDR. LOW
Table 22-8 on page
B
DATA LOW
(1)
C
F
DATA HIGH
D
for details on Command, Address and
XX
E
171. When programming the
ADDR. HIGH
G
H
XX
Figure 22-4
2588B–AVR–11/06
for