P89LPC982FDH,529 NXP Semiconductors, P89LPC982FDH,529 Datasheet - Page 41

• Manufacturer Part Number: P89LPC982FDH,529
• Description: MCU 80C51 8KB FLASH 28TSSOP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC982FDH,529

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 28-TSSOP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 26
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 5
• Operating Supply Voltage: 2.4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935290303529

NXP Semiconductors
P89LPC980_982_983_985
Product data sheet
7.17.1 Brownout detection
7.17 Power management
Please refer to P89LPC980/982/983/985 User manual for detail configurations.
Table 10.
The P89LPC980/982/983/985 support a variety of power management features.
Power-on detect and brownout detect are designed to prevent incorrect operation during
initial power-up and power loss or reduction during operation.
The P89LPC980/982/983/985 support three different power reduction modes: Idle mode,
Power-down mode, and total Power-down mode. In addition, individual on-chip
peripherals can be disabled to eliminate unnecessary dynamic power use in any
peripherals that are not required for the application.
Integrated PMU automatically adjusts internal regulators to minimize power consumption
during Idle mode, Power-down mode and total Power-down mode. In addition, the power
consumption can be further reduced in Normal or Idle mode through configuring
regulators mode according to the applications.
The brownout detect function determines if the power supply voltage drops below a
certain level. Enhanced brownout detection has 3 independent functions: BOD reset,
BOD interrupt and BOD flash.
These three functions are disabled in Power-down mode and Total Power-down mode. In
Normal or Idle mode, BOD reset and BOD flash are always on and can not be disabled in
software. BOD interrupt may be enabled or disabled in software.
BOD reset and BOD interrupt, each has 6 levels. BOE0 to BOE2 (UCFG1[3:5]) are used
as trip point configuration bits of BOD reset. BOICFG0 to BOICFG2 in register BODCFG
are used as trip point configuration bits of BOD interrupt.
BOD reset voltage should be lower than BOD interrupt trip point. BOD flash is used for
flash programming/erase protection and has only 1 trip point at 2.4 V. Please refer to
P89LPC980/982/983/985 User manual for detail configurations.
If brownout detection works, the brownout condition occurs when V
brownout falling trip voltage and is negated when V
voltage.
Peripherals
SPI
I2C
UART
SPI/I2C/UART pin remap
Function
SPICLK
MOSI
MISO
SS
SDA
SCL
TXD
RXD
Rev. 4 — 15 June 2010
8-bit microcontroller with accelerated two-clock 80C51 core
Primary pin out
P2.5
P2.2
P2.3
P2.4
P1.3
P1.2
P1.0
P1.1
P89LPC980/982/983/985
DD
rises above the brownout rising trip
Alternative pin out
P0.0
P1.7
P1.6
P1.4
P2.7
P2.6
P2.0
P2.1
DD
falls below the
© NXP B.V. 2010. All rights reserved.
41 of 85