P89LPC982FDH,529 NXP Semiconductors, P89LPC982FDH,529 Datasheet - Page 58

• Manufacturer Part Number: P89LPC982FDH,529
• Description: MCU 80C51 8KB FLASH 28TSSOP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC982FDH,529

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 28-TSSOP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 26
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 5
• Operating Supply Voltage: 2.4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935290303529

NXP Semiconductors
8. ADC (P89LPC983/985)
P89LPC980_982_983_985
Product data sheet
7.29.10 Hardware activation of the bootloader
7.30 User configuration bytes
7.31 User sector security bytes
8.1 General description
Remark: Users who wish to use this loader should take precautions to avoid erasing the
1 kB sector that contains this bootloader. Instead, the page erase function can be used to
erase the first eight 64-byte pages located in this sector.
A custom bootloader can be written with the Boot Vector set to the custom bootloader, if
desired.
Table 11.
The bootloader can also be executed by forcing the device into ISP mode during a
power-on sequence (see the P89LPC980/982/983/985 User manual for specific
information). This has the same effect as having a non-zero status byte. This allows an
application to be built that will normally execute user code but can be manually forced into
ISP operation. If the factory default setting for the boot is changed, it will no longer point to
the factory pre-programmed ISP bootloader code. After programming the flash, the status
byte should be programmed to zero in order to allow execution of the user’s application
code beginning at address 0000H.
Some user-configurable features of the P89LPC980/982/983/985 must be defined at
power-up and therefore cannot be set by the program after start of execution. These
features are configured through the use of the flash byte UCFG1 and UCFG2. Please see
the P89LPC980/982/983/985 User Manual for additional details.
There are four/eight User Sector Security Bytes on the P89LPC980/982/983/985. Each
byte corresponds to one sector. Please see the P89LPC980/982/983/985 User manual for
additional details.
The P89LPC985 has a 10-bit, 8-channel multiplexed successive approximation
analog-to-digital converter modules. The P89LPC983 has a 10-bit, 4-channel multiplexed
successive approximation analog-to-digital converter modules. A block diagram of the
ADC is shown in
Device
P89LPC980
P89LPC982
P89LPC983
P89LPC985
Default boot vector values and ISP entry points
Figure 20 “ADC block
Default
boot vector
0FH
1FH
0FH
1FH
Rev. 4 — 15 June 2010
8-bit microcontroller with accelerated two-clock 80C51 core
Default
bootloader
entry point
0F00H
1F00H
0F00H
1F00H
P89LPC980/982/983/985
diagram”.
Default bootloader
code range
0E00H to 0FFFH
1E00H to 1FFFH
0E00H to 0FFFH
1E00H to 1FFFH
© NXP B.V. 2010. All rights reserved.
1 kB sector
range
0C00H to 0FFFH
1C00H to 1FFFH
0C00H to 0FFFH
1C00H to 1FFFH
58 of 85